background image

Gates Underwater Products, Inc 

13685 Stowe Drive • Poway, CA • 92064 • 858.391.0052 • 800.875.1052 • Fax 858.391.0053 

[email protected] • www.GatesHousings.com 

01/13/10  

23 

 
 

 

 

Optional Water Alarm

 

If your EX1R housing includes the optional water alarm, there are three alarm conditions 
to watch for: 

 

You can test the alarm anytime by shorting the detection contacts that lead to the water 
alarm transducer.  The water detection condition will activate for 6 seconds.  If the 
battery is low, the low battery condition will sound.   

The water alarm requires a single 6V battery like Radio Shack model 23-469 or A544. 

Your battery should be removed when stored (e.g. between dive trips).  Check the 
battery prior to every dive to ensure proper operation, and change when indicated.  

You 

must wait a minimum of 30 seconds between battery insertions to allow unit to 
fully discharge.

 

   

Condition LED  Siren 

 

 

 

New battery  

(when inserted) 

 

Bright intense blink while siren 

plays. 

Ascending tones played 4 

times. 

 

Water intrusion 

Bright intense blink. 

Grating warble sound.  Alarm 

will sound for duration of 
detection 

 

Low battery 

Low intensity fast blink. 

Descending tones played 8 

times pausing approximately 

20 seconds between plays 

after alarm test or water 
detection.  

 

Summary of Contents for EX1R



























Reviews: