Gates Underwater Products EX1R Setup, Use And Care Manual Download | Manualshive

Page: 24 / 26

background image

Gates Underwater Products, Inc

13685 Stowe Drive • Poway, CA • 92064 • 858.391.0052 • 800.875.1052 • 858.391.0053

[email protected] • www.GatesHousings.com

24

01/13/10

Optional External Monitor

This section covers

mounting

of the optional monitor to the EX1R housing and

connection to the camera. Refer to the Setup, Use and Care guide for the monitor to be
used with the EX1R housing for other details. The Gates EM43 monitor is shown here
for reference.

Camera connection and setup

9

Connect to the camera

by plugging in the video cable located inside the housing.

The video cable will plug into the component connector on the right side of the
camera, just below the rec/stdby button.

9

Verify operation.

You can check proper operation at this time by plugging in the

monitor (see below) and turning on the camera. The camera must be setup to
display recording data and other information on the monitor by setting the following
menu selection:

MENU

Æ

VIDEO SET

Æ

YPbPr/SDI OUT DISPLAY

Æ

ON

The monitor cable plugs in
here.

«
...
22
23
24
25
26
»

Summary of Contents for EX1R



























Reviews:

No comments

Related manuals for EX1R

Brand: KC HiLiTES Pages: 4

Brand: CAME Pages: 4

DWSC - Vintage C

Brand: Daikin Pages: 57

Brand: e-Line Technology Pages: 36

Brand: F&F Pages: 8

Brand: RAKINDA Pages: 20

Brand: ZALMAN Pages: 20

Brand: ibis Pages: 12

Brand: IAME Pages: 17

Brand: Waldbeck Pages: 7

Aerasgard KCO2-W

Brand: S+S Regeltechnik Pages: 16

Brand: Atlas Copco Pages: 88

Brand: Filmcity Pages: 9

Car Top Duffle Bag

Brand: Rightline Gear Pages: 2

OADM 20I6480/S14F

Brand: Baumer Pages: 4

Brand: Balluff Pages: 122

Brand: ECS Electronics Pages: 16

Brand: Jetmaster Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands