background image

www.gastron.com

12

_

13

5. Installation 

5. Installation 

GTC-550

Instruction Manual

[Figure 3. CN6 Terminal Configuration]

[Figure 2. GTC-550 Power Configuration]

■ 

It is prohibited for an individual, other than an approved user or a technician responsible for installation and repair 

  from the head office, to install a gas leak detector on site or open the cover of the installed gas leak detector and 

  manipulate it. This may cause serious loss of life and property from fire, explosion, and etc. In addition, please 

  check whether there is any remaining explosive gas or combustible material in the surroundings. Power must be 

  turned off before performing work.

5.1. Power Configuration

■ 

When it is desired to use DC24V, a separate request must be made when ordering the product. When the product

  has been delivered as DC24V-Type upon a customer request, (+) and (-) of DC24V shall be connected to L1 and

  L2 or CN9, respectively.

■ After detaching the equipment cover, terminal block that connects power and various signals within PCB appears.

■ Connect AC Power (85~260 V 50/60 Hz) to CN9 as shown in the figure below.

5.2. Signal Terminal Configuration

■  Using CN6 terminal, connect 4~20 mA output, External Reset, RS485, and external gas detector. 

  Terminal configuration is as shown in the table below.

■ RS-485 cable uses a cable designated for RS-485 and cables for 4~20 mA output and detector connection must  

  use a shield cable with CVVS or CVVSB 0.75 sq and higher.

[Table 2. CN6 Terminal Description]

Note 1) When RS485 Option does not exist, RS485 function does not operate.

FUNCTION

TERMINAL NAME

DESCRIPTION

4-20mA 

Output

VISO

External power input terminal for 4~20 mA Sink Driver

mA

Output terminal for 4~20 mA Source Driver

SENSOR

Combustible Sensor

Toxic Sensor

O2 Sensor
(Galvanic Method)

1

Red Cable

Blue Cable

N.C

2

White Cable

Red Cable

Red Cable

RESET

+

External Reset S/W + Terminal. When + and - terminals short, alarm reset function 
operates.

-

External Reset S/W - Terminal

RS485

A

RS485 A Terminal (TRXD+ or P)

B

RS485 B Terminal (TRXD+ or N)

Summary of Contents for GTC-550





















Reviews: