manualshive.com logo in svg

Gasmate Ignite BQIG10, Manual, Page: 15 / 16

Share
Download
Gasmate Ignite BQIG10 Manual Download Page 15

14

15

WARNINGS

• Improper installation, adjustment, alteration, 

service or maintenance can cause injury or 

property damage.

• Read the instructions thoroughly before 

installing or servicing this equipment.

• THIS APPLIANCE MUST NOT BE INSTALLED 

OR USED INDOORS.

• NATURAL GAS APPLIANCE. TO BE INSTALLED 

ONLY BY AN AUTHORISED PERSON.

• THE AUTHORISED PERSON WILL PROVIDE A 

CERTIFICATE OF COMPLIANCE.

• A suitable AGA approved natural gas pressure 

regulator must be installed in the pipeline and 
be set at 1 kPa.

NATURAL GAS CONVERSION

TO BE INSTALLED ONLY ON OR IN A 

NON-COMBUSTIBLE ENCLOSURE

Note: Recommended clearances must be maintained.

Tools Required: 

• Adjustable spanner
• Phillips head screwdriver

GAS PIPING 

1. (a) A minimum pipe diameter of 15mm is 

required for inlet piping. A lever operated 
shut-off valve should be installed within 1 
metre of the appliance for servicing the unit.

  (b) Where it is not practical to install solid tube 

AGA certified stainless steel braided hose 

can be installed. This hose assembly must 
comply with AS5601 Gas Installations, pipe 

sizing tables and shall not exceed 3 metres 

in length. The internal diameter of the hose 
must not be less than 10mm.

2. Check with local and state plumbing and 

heating codes regarding sizing of the gas lines.

3. All gas pipe connections must be sealed with a 

gas pipe compound resistant to Natural Gas.

4. Installation of a drip leg if required in the gas 

supply line must conform to AS5601.

5. When checking for gas leaks, do not use an 

open flame.  Use a soap and water solution and 

check for bubbles indicating gas leakage.

6. Installation of 1/8” NPT pluggedtapping, 

accessible for test gauge connections, 
is required upstream of the gas supply 
connection.

Warning 

Improper installation, adjustment, alteration, 

service or maintenance can cause injury 

or property damage. Read the instructions 

thoroughly before installing or servicing this 

equipment.

SERVICING INSTRUCTIONS

Appliances should be serviced at least annually 
and servicing must only be carried out by a 

Licensed Plumber or Authorised Person.

Clean the Burner Ports and top with a Soft Brush. 

Inspect and clean all combustion air inlets, then 

replace the Burner ensuring it is firmly secured.

Minimum Clearance for Ventilation:

Rear: 60mm 

Above: 500mm

Side: 150mm 

Below: 200mm

NOTE TO INSTALLER:

1. The gas valve plug by-pass orifices must be 

increased to:

  BBQ Burner 

- High  -  No Change 

 

 

- Turndown   1.40mm

2. BBQ Burner: Drill the injectors as per the data 

label specifications or contact customer service 

on 1300 174 876 to order an injector kit.

TEST OPERATION OF APPLIANCE  
BEFORE LEAVING.

Conversion ONLY to be done by an authorised person.

Summary of Contents for Ignite BQIG10

















Reviews:

No comments