background image

GASBOY FleetKey 

 

03/07/03 

INSTALLATION OF KEY SYSTEM 

 
1.  From the conversion kit, press the Trim Edge Material onto the bottom edge of the PCB 

Mounting Bracket

 
2. Using 

the 

four screws from the conversion kit, secure the Key I/F PCB to the PCB 

Mounting Bracket

 
3. 

From the outside of the unit, insert the two threaded studs of the provided single or dual Key 
Adapter Bracket
 into the two mounting holes in the face of the unit that were used to mount 
the mag card reader.  Verify that the four slots in the Key Adapter Bracket line up with the 
four holes in the face of the unit.  If they do not, the bracket is installed incorrectly and should 
be rotated. 

 
4. 

Working inside the head of the unit, align the two slotted holes of the PCB Mounting Bracket 
onto the two threaded studs of the Key Adapter Bracket.  Secure the brackets together with 
two of the hex keps nuts provided in the conversion kit. 

 
5. 

There are two braided ground straps of different lengths provided in the conversion kit, but 
only one will be used.  The location of the ground studs on your system determines which 
cable you will use.  One ground stud is located on the PCB Mounting Bracket. 

 

• 

If there is a ground stud to the side of the bracket (on the base of the head), use the short 
ground strap.  The short strap is mounted between the ground stud on the PCB Mounting 
Bracket and the ground stud right next to the bracket.   

 
  

Place 

the 

provided 

star washers onto the ground studs, then the ring terminals of the 

ground straps, and secure them in place with the provided hex keps nuts

 

• 

If no ground stud is next to the bracket, use the long strap and make the connection 
between the PCB Mounting Bracket and the ground stud located near the hinge of the 
rear door.  This stud already holds a ground wire to the rear door.  

 
 

 

Secure one end of the strap to the ground stud on the PCB Mounting Bracket by first 
placing a provided star washer on the stud, then the ring terminal of the strap, and then a 
provided hex nut.   

 
 

 

Remove the existing hex nut on the rear ground stud and place the ring terminal on the 
stud with the existing ground wire.  (If there is not a star washer under the existing ground 
strap, add one at this time).  Replace the hex nut. 

 
6. Install 

the 

Key Receptacle(s) by standing in front of the Series 1000 and snapping them into 

the hole(s) in the Key Adapter Bracket.  Be sure the PCB connector of the Key Receptacle 
is facing upward before snapping it in place. 

 
7.  Reinstall the external cover assembly that was removed in step 4 (mag) or steps 5 & 6 

(optical).  Hold the cover in place over the Key Receptacle(s), be sure the cover will open 
upward.  Working inside the head of the unit, use the four previously removed screws to 
secure the external cover to the face of the unit. 

 

Summary of Contents for SERIES 1000























Reviews: