manualshive.com logo in svg

GarrettCom DynaStar DS2000-TS, Administrator'S Manual, Page: 26 / 122

Share
Download
GarrettCom DynaStar DS2000-TS Administrator'S Manual Download Page 26

C

HAPTER

2 - 

Supervisor Overview

Supervisor Menus

DS2000-TS Administrator’s Guide

2 - 8

Figure 2-6. Port Status Menu

Selecting a port from either the 

Port Selection

 menu or the 

Port Status

 menu, displays the 

Port Functions

 

menu as shown in 

Figure 2-7

. From the 

Port Functions

 menu the user can select to:

•

Configure the port

•

Obtain Statistics on the port

•

Disable or Enable the port

•

Use the Protocol monitor to view the traffic being passed on the port

Appendix A, “Port Functions” in the rear of this manual provides details on the Port related menus.

Figure 2-7. Port Functions Menu

                              *** Port Status ***
DynaStar 2000                                                 12-11-05  7:33:55

                  Ethernet        SLOT 1          SLOT 2
Port number:      E0              S1 - S16        S17 - S32
Name:             Ethernet        MUSART          MUSART
Interface:        IS-Enet
Protocol:         Ethernet
State:            Enabled
Status:           Link Down

                  Sync/Async      HS WAN 1        HS WAN 2        Console
Port number:      S0                                              CON
Name:             Sync/Async      No board        No board        Console
Interface:        RS-232                                          RS-232
Protocol:         PAD                                             Console
State:            Enabled                                         Enabled
Status:           Down                                            Up - 1

                 Enter slot # to view status of multiple-port module:

_________[DynaStar_6b2c]__________                       Enter Port Number:
                                          Press ESC to return to previous menu

                          *** Functions For Port S1 ***

 1 - Configuration          Configure protocol and port parameters
 2 - Statistics             Display port statistics
 3 - Disable/Enable         Disable, enable, initialize or busy
 4 - Protocol Monitor       Display transmitted/received data packets

                            Enter command number:
_________[DynaStar_6b2c]__________
Terminate input with <RET>             Press ESC to return to previous menu

Summary of Contents for DynaStar DS2000-TS



























































































































Reviews:

No comments