English
36/184
Do not use this machine at night, with fog or low
visibility which will not allow you to see the working
area clearly.
Keep the work area clean and work with good
lighting.
Only use this machine with daylight or with good
artificial light. Cluttered and dark areas cause
accidents. Inspect and remove any objects that can
cause damage to you or the machine.
Do not use this machine in areas where there is
wiring or underground pipes. Inspect your work
area and remove all stones, wood, wire, and foreign
objects that may be dismissed by the cutting tool.
2.4. SAFETY IN THE USE OF FUELS
IMPORTANT: The fuel used for this machine
is highly flammable. If the fuel or the
machine ignites, smother the fire with a dry
powder fire extinguisher.
Petrol and oil are hazardous; avoid contact
of gasoline or oil with the skin and eyes. Do
not inhale or swallow them. Immediately
see your doctor if you ingest fuel or oil. If they come
into contact with fuel or oil clean with soap and water
as soon as possible, if you then continue to feel
irritated skin or eyes immediately consult a doctor.
Do not refuel fuel in closed or poorly ventilated
places. Fumes from the fuel and oil contain
hazardous chemicals. In the case of a concentration
of gases produced by insufficient ventilation, remove
all that impedes the flow of clean air from the area
in order to improve ventilation. Do not return to the
area unless you have properly ventilated the area
and are certain that ventilation is sufficient so this
concentration does not happen again.
Petrol and oil are extremely flammable and explosive
under certain conditions. Do not smoke and keep
flames, sparks or heat sources away from the
machine.
Do not smoke while transporting fuel, when you fill
out the deposit or when you are working.
Do not refuel fuel in locations where there is the
presence of open flames, sparks or heat sources. Fill
the tank always in well-ventilated areas and with the
motor stopped. In the event of a fuel leak, be sure to
clean these leaks completely before starting, move
the machine away from the spillage area and avoid
any source of ignition until all vapors are gone.
Add fuel before starting the machine. Never remove
the cap of the fuel tank while the engine is running or
when the machine is hot.
Make sure the cap of the fuel is tightly and correctly
closed while you are using the machine. Make sure
to correctly and tightly close the cap on the fuel after
refilling.
Always store fuel in approved containers that comply
with the European standards.
2.5. CARE AND USE OF THIS MACHINE
Only cut grass. Do not use this machine for other
purpose not intended. For example: do not use the
Summary of Contents for SIOUX 1455 ZSL
