![background image](http://html1.mh-extra.com/html/garland/mule-1482-nrqg/mule-1482-nrqg_instruction-manual_3634581047.webp)
English
English
47/180
Do not use any accessory on this machine outside of
those recommended by Garland since its use could
result in serious injury to the user, machine, and the
people, animals and things close to the machine.
6.4.1.1. CLUTCH CHECKPOINT
The cutting tool should be off by default to prevent
the machine from moving at the time of starting the
machine. To verify that the clutch is disengage, place
the switch to “OFF” position and pull slowly and
forcefully from the Starter handle the engine turn.
Note If, while the motor spins, also turn the cutting
tool. If the cutting tool rotates, it means that the clutch
is engaged and is therefore poorly regulated. If the
clutch is not correctly regulated take your machine for
service.
6.4.2.STARTING THE ENGINE
Start the engine carefully, in accordance with the
instructions, and feet away from the milling cutters.
6.4.2.1. COLD-STARTING THE ENGINE
Place the machine on a flat surface and stable to start
it.
1. Place the ON/OFF switch in the “ON” position.
2. Place the fuel tap in the open position.
3. Place the air lever in the Closed position .
4. Place the accelerator lever in the maximum
position. .
5. Place yourself behind the machine, as shown in the
figure, and pull the Starter rope until the engine
starts.
6. If the machine starts and does not stop, slowly
begin moving the air lever toward the Open air
position (normal working position).
7. Adjust the appropriate number of revolutions with
the throttle lever.
8. Allow the engine to warm up for a few minutes
before starting to use the machine.
6.4.2.2. STARTING WITH A HOT ENGINE
Place the machine on a flat surface and stable to start
it.
1. Place the ON/OFF switch in the “ON” position.
2. Place the fuel faucet in the Open position.
Normal working
position
Turtle = Minimum
Hare = Maximum
Summary of Contents for MULE 1482 NRQG
