English
English
53/172
8.2. OTHERS
Carry out periodical inspections with the aim
of ensuring a safe and efficient performance
from the tool. For a complete inspection of
the tool, please contact your distributor.
Keep the machine clean, especially the areas near the
gas tank and air filter.
Before adjusting or repairing the machine, make sure
the engine is stopped and the cover of the spark plug
has been removed.
Use the appropriate parts in order to obtain a safe and
adequate performance from the product. These parts
can be obtained from your distributor.
The use of other accessories could can
cause potential risks, injuries to the operator
or damage to the machine.
8.2.1. AIR FILTER
The obstruction of the air filter will cause the
performance of the engine to decrease. If necessary,
inspect and clean this element. If any damage or
alteration is observed, replace it with a new one.
To clean the dirt on the filter open the cover unscrew
the lid and remove the filter.
The dust on the
surface of the filter
can be removed by
hitting a corner of the
filter against a hard
surface.
8.2.2. ADJUSTMENT OF THE CARBURETOR
Carburetor regulation is complicated and
we recommend it is done by a person with
experience or by the customer service.
Do not adjust the carburetor unless it is necessary. If
any problems with the carburetor are observed, see
your distributor.
The incorrect adjustment of the element could
damage the engine, as well as causing the warranty
to be cancelled.
8.2.3. FUEL FILTER
The fuel tank is provided
with a filter (1). This element
is located at the extreme
end of the fuel hose and
it can be removed fuel
opening with the help of a
piece of wire bent into a
hook or similar device.
Inspect the fuel filter periodically. Do not allow dust
to enter the fuel tank. The obstruction of the filter will
make it difficult to start the engine or it will produce
abnormalities in the performance of the engine.
Inspect the fuel filter and if it is dirty, replace it with a
new one.
If the inside of the fuel tank is dirty, it can be cleaned
by rinsing out with petrol.
8.2.4. OIL FILTER
The oil tank is provided with a filter (2). This element
is located at the extreme end of the oil hose and it
can be removed oil opening with the help of a piece of
wire bent into a hook or similar device.
Summary of Contents for MONTANA 920
