![background image](http://html1.mh-extra.com/html/garland/montana-920/montana-920_instruction-manual_4327139046.webp)
English
46/172
Before starting the engine, move at least 3 meters
away from the place where the fuel was added.
Sepárese al menos 3 metros de la zona en la que ha
repostado antes de arrancar la máquina.
6.3.3. CHAIN OIL
Only special lubricating oil for chain saws
must be used.
Do not use used oil as this could damage
the oil pump.
Chain oil must be introduced into the chain
oil reservoir.
You can recognize this deposit by the
pictogram (indicated in Chapter 4,
“Symbols on the machine).
6.4. OPERATING
Before starting the engine, ensure no moving parts of
the tool are in contact with anything.
Once the engine has started, make sure the chain
stops when the throttle trigger is released.
Hold the tool firmly with both hands, strongly gripping
the hangles when the engine is running.
It is necessary to pay attention to the possible
loosening or overheating of the parts. If any
abnormalities are detected in the machine, stop
working immediately and inspect the machine
carefully. If necessary, take the machine to an
authorized distributor to be repaired. Under no
circumstance must the work continue, if the tool is not
operating correctly.
Do not use the machine if it is damaged or incorrectly
adjusted.
Keep the handles clean, dry and free from oil or fuel.
6.4.1. STARTING UP WITH THE ENGINE COLD
1. Move the ignition switch to the START position (1).
2. Press the engine primer repeatedly (7-10 times)
until the fuel reaches the primer.
3. Pull the choke lever (3).
4. When the tool is placed on the ground, it must be
put in a horizontal and stable place.
5. Hold the tool firmly with the left hand on the front
handle and a foot placed through the back handle.
Summary of Contents for MONTANA 920
