Garland HEEGM48CL Service Manual Download Page 3

Page: 3 / 44

Page 3 | HEEGM Service Manual part# 4532502 (Rev 0)

CONTENTS

1 SAFETY REQUIREMENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Warnings and Important Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2 RATING PLATE, SERIAL#, MODEL# INFORMATION

. . . . . . . . . . . . . . . . . . . 6

2.1 Rating Plate Location

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.2 Serial Number (Year/Month Information)

. . . . . . . . . . . . . . . . . . . . . . . . .6

2.3 Model Code

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3 TECHNICAL SPECIFICATIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3.1 Gas Requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.2 Manifold Pressure

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

3.3 Electrical Requirements

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

4 UNIT CONFIGURATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.1 Important Features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

4.2 Major Components - Quantity Comparison

. . . . . . . . . . . . . . . . . . . . . . .8

4.3 Major Components Illustrated

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

5 TROUBLESHOOTING GUIDE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

5.1 Sequence of Operation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

5.2 Troubleshooting Flowchart

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

5.3 Problems & Evaluation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

6 REMOVE, INSTALL AND ADJUST COMPONENTS

. . . . . . . . . . . . . . . . . . . . 16

6.1 Knob

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

6.2 Valve Panel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

6.3 Side Leg Panels - Left / Right

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

6.4 Gas Pressure Regulator & Gas Pressure

. . . . . . . . . . . . . . . . . . . . . . . . . .18

6.5 Burner and Air Shutter

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

6.6 Gas Valve

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

6.7 Orifi ce

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

6.8 Electrode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

6.9 Solenoid Valve

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

6.10 Ignition Module

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

6.11 ON-OFF Switch & Main Power Switch

. . . . . . . . . . . . . . . . . . . . . . . . . .31

6.12 Transformer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

7 WIRING DIAGRAMS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

HEEGM24CL 120VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

HEEGM24CL 240VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

HEEGM36CL 120VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

HEEGM36CL 240VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

HEEGM48CL 120VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

HEEGM48CL 240VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

HEEGM60CL 120VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

HEEGM60CL 240VAC

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

8 RELATED DOCUMENTS & REVISION HISTORY

. . . . . . . . . . . . . . . . . . . . . . 42

Summary of Contents for HEEGM48CL













































Search results

Summary of Contents for HEEGM48CL

Reviews:

Brands by name

Popular brands

Garland HEEGM48CL, Service Manual

Search results

Summary of Contents for HEEGM48CL

Reviews:

Brands by name

Popular brands