background image

Română

46/184

In case of any malfunction or problem take the 
machine to a service technician to be repaired.

Under no circumstances must you continue to 
use the machine if the operation does not seem 
appropriate.
Do not use the machine if it is damaged or 
improperly adjusted.

 7. USING THE MACHINE

 Use this machine only for the designated 

purposes. Using this chainsaw for any other use 
is dangerous and can cause bodily harm and/or 
damage to the machine.

Do not start the machine in a room or 
enclosure. The exhaust gases and fuel 

and oil vapors contain carbon monoxide and harmful 
chemicals. In case of a concentration of gases 
produced by poor ventilation, remove all that impedes 
the flow of clean air to improve ventilation from the 
work area and not return to work in the area unless 
you have properly ventilated area and have clear that 
ventilation is sufficient so that does not happen this 
concentration again.

Work only in daylight or good artificial light. Do not 
use this machine at night, with fog or with a low 
visibility which do not allow you to clearly see the 
working area.

Whenever possible, avoid using this machine when 
the ground is wet. Pay special attention if you use 
this machine when it is raining or after it has rained, 
as the ground will be slippery and you could slip 
and fall.

Do not use this machine on slopes greater than 15°. 
Cutting on hilly areas can be dangerous.

Be alert when you walk on slopes or wet grass. 
Slopes always cut horizontally, not cut bottom up 
or top down. Be especially careful when changing 
direction on a slope.

Never cut with the mower in reverse or by pulling 
it. Be alert when you back up or pull the mower 
towards you.

Do not tilt the machine with the engine running 
except in the special case that you have to start 
cutting an area with tall grass. This is the only case 
in which you can raise the front wheels slightly 
to facilitate entry of the mower to the work area. 
Stop the lawnmower’s engine if you tilt it to cross 
surfaces other than grass and when transporting the 
lawnmower to and from the area to be cut.

Do not go near the machine’s cutting 
tool when it is running. Danger! Risk 
of finger amputation.

Keep hands and feet away from the blades.

Do not solely rely on the security features of this 
machine.

It is necessary to pay attention to the possible 
loosening or overheating of the parts of the machine. 
If you detect any anomaly immediately stop the 
machine and check it carefully.

In case of mechanical failure take the machine to the 
technical service for repair. You should not continue 
working if you notice that the operation is not correct.

D

DANGER

ANGER

DO NOT USE MOWER WITHOUT ENTIRE

GRASS CATCHER OR DEFLECTOR IN PLACE

KEEP HANDS and FEET AWAY

Summary of Contents for APACHE 675 SL
































Reviews: