background image

6 T-BA/ET-1250-0-GB-

10

-

11

2.0 Safety

Alterations, attachments or conversions to the
rotary compressor/compressor vacuum pump,
which may affect safety, are not permitted without
consulting the manufacturer.

All warnings on the machine must be observed
and must be kept in a fully legible condition.

Fire alarm and firefighting possibilities must be
observed.

Work on electrical equipment must only be carried
out by a qualified electrician.

Before carrying out any work, the staff
instructed to work on the machine must
have read the chapter in the operating
manual entitled “Safety Regulations”.  

Doing so once work has started is too
late!

Work may only be carried out on the machine
when it is at a standstill.

Before starting work, secure the machine to pre-
vent restarting.

The system must not be pressurized or contain a
vacuum when work is being carried out on the
machine.

Vehicle side: Close shutoff valve. Vent, respec-
tively aerate delivery pipe between system and
shut-off valve.

Use the safety valve so as to manually release
excess pressure, respectively vent the machine by
means of the ventilation valve.

Note pressure gauge reading!

Only remove the safety devices from the drive
when the machine is at a standstill.

The shock-hazard protection may only be removed
when the machine and the delivery pipe has coo-
led down.

Before starting the machine, ensure that all protec-
tive fixtures have been reattached.

Environmental safety requires the collec-
tion and safe disposal of all fluids that
may escape during maintenance work,
e.g. lube oil.

Summary of Contents for Wittig SLS 34



























Reviews: