background image

Maintenance and Servicing 

 

26 

 

P1700040 

 

 

 

 

1 - 

Oil fill plug 

2 - 

Oil drain plug 

3 - 

Lower marking MIN  

4 - 

Oil sight glass  

5 - 

Upper marking FULL  

 

 

 

 

Fig. 11   Oil level control 

 

6.2  Oil Colour Check 

 

 

WARNING! 

The condition and quality of the pump oil have a substantial effect upon the 
performance and operational readiness of the vacuum pump! 

 
Comparing the colour of a sample of the pump oil with fresh oil provides an indication of the 
contamination of the pump oil. You obtain the oil needed for testing from the oil drain aperture with the 
vacuum pump switched off and at operating temperature.  
 
Brown or black oil or oil smelling as if it has burnt must be removed from the vacuum pump. Flush the 
vacuum pump and fill up with fresh oil. 
 

6.3  Oil Change 

 

 

WARNING! 

If the vacuum pump has been used to pump media which are dangerous to health then 
all measures must be taken to protect the service and operating personnel! 

 

6.3.1  Draining the Oil 

 

1.  Block the inlet port and switch on the vacuum pump and let it work for about 10 minutes to 

warm the oil. 

2.  Switch off the pump, disconnect from the power outlet and from the vacuum system. 

3.  Unscrew the oil drain plug from the pump casing while the pump is at operating 

temperature.  

4.  Tilt the vacuum pump slightly, catches the oil in a suitable vessel and dispose of it in 

accordance with the applicable regulations. 

Summary of Contents for WELCH CRVpro Series

















































Reviews: