background image

Operation Manual

 

 

 

 

 
 

 

 

 
 

To  aid  re-assembly,  note  which  components 
came off which shaft. Good engineering practise 
suggests  that  components  removed  from  a 
shaft should be assembled on the same shaft. 

 

If removing the front cover for any reason 
check that rotorcase retaining nuts are tight 
before replacing.

 

 

8.2 Removing the front cover

 

 

 

1.        Remove  the  'R'  clips  (2)  and  carefully 

loosen  the  front cover  retaining  nuts (3) 
as there may still be residual pressure in 
the system. 

 

2.      Remove the front cover nuts and take off 

the cover (6). If stuck, loosen by tapping 
with soft mallet at overlap at sides. 

Do not lever off.

 

 

3. 

Flush out the pump head before 
continuing. 

 

4.        Remove  the  'O'  ring  (7)  from  the  front 

cover. 

 

8.3 Removing the rotors

 

 

 

1. 

Insert a plastic block between the two 
rotors (13) to stop them turning. 

 

2.      Using  a spanner  remove  the  rotor  nuts 

(9). These nuts have right hand threads. 

 

 

3.      The rotors can be removed from the shafts 

(28,29) by hand or by using the extractor 
tool  supplied  with  the  pump  to  aid 
disassembly.  Unscrew  the  central  bolt 
until flush on the inside, screw the tool two 
full turns into the rotor. Whilst preventing 
the tool from turning screw in the central 
bolt. The rotor is jacked off the shaft for 
hand removal. 

 

 

 

 
 

 
 

 

 

 
 

 
 

 

 

 

Central bolt

 

 
 

 
 

 

 

 
 

 
 

 

 

 
 

 

8.4 Product seal removal

 

 

 

1. 

'O' ring- Refer to section 10 

 

 

2. 

Mechanical Seal - Refer to section 11 

 

 

8.5 Removing the rotorcase

 

 

 

1. 

Remove the rotorcase retaining nuts. (5). 

 

 

2.      Gently tap the rotorcase (11) on each side 

with  a  soft  mallet  to  release  it from  the 
bearing housing. (18) 

 

3. 

The rotorcase will be supported on 
the studs (4) during removal. 

 

4.      The rotorcase and seal housing (66) can 

be removed as an assembly. 

STP125    Page  18

 

Summary of Contents for STP 125









































Reviews: