background image

Operation Manual

 

 

 

 
 

6.3 Cleaning In Place (CIP)

 

 

The pump can be manually cleaned or 
cleaned in place(CIP). The following is an 
example of a typical CIP procedure. Specific 
requirements for each application should be 
dictated by the carrier/shipper. 

 

Determine last product handled by the 
pump 

 

Remove the dust caps and/or fittings 
from the pump, rinse any residue from 
them with hot water. 

 

Connect hot water hose to the pump 

inlet or connect pump inlet to the tank 
trailer outlet valve during the tank

’s 

hot water cleaning cycle. 

 

 

When not fitted connect a ball or gate 
valve (to restrict liquid flow) to the 
pump discharge outlet. 

 

If driven hydraulically, ensure that the 
hydraulic proportional control valve  is 
in the neutral position. 

 

If driven hydraulically or electric/ 
hydraulically, start system and run at 
normal operating speed.  Open the 
ball or gate valve on the pump 
cleaning system so the hot water or 
cleaning solution from the tank flows 
into the pump. (hot water should be 
176°F to 194°F) If hydraulically driven, 
select forward on the proportional 
control valve and slowly increase (by 
pushing the handle) to full pump speed. 
When driven electrically start the 
system and slowly increase the speed 
with the handwheel on the belt variator. 

 

Using the ball or gate valve, (to 
restrict liquid flow) increase the pump 
pressure to approximately 60-75 psi 
while it is operating. A pressure gauge 
at the discharge outlet will be required. 
This will ensure that the cleaning 
solution is cleaning the pump under 
high pressure conditions. 

 

Run the pump for 15 minutes under this 
pressure. 

 

Relief Valve Pumps Only

 

WARNING: Do not complete this next 
step if your pump does not have a 
relief valve !!

 

 

Close the ball or gate valve (to restrict 
liquid flow) until the pump relief valve 
actuates. Open the valve and close it 
again. Open valve once again - this 
should have now cleaned any residue 
from behind the relief valve diaphragm 
and any other close tolerance areas 
inside the pump. 

 

Shut down pump system in reverse 
order of above. 

 

Clean all external fittings from the 
fittings box with hot water and return. 

 

Remove all hose and fittings from the 
pump, bag ends and seal the ports. 

 

 

IMPORTANT

 

Do not subject the pump to rapid temperature 
changes as pump seizure can result from thermal 
shock. 

STP125    Page  15

 

Summary of Contents for STP 125









































Reviews: