13
6.4 Control Board Jumpers
In the upper left hand corner of the control board there
are eight two-pin jumpers labeled JP1 through JP8. Only
six of the eight jumper pairs are utilized. Pairs JP7-JP8
are used for factory settings and testing.
NOTE: Do
not install jumpers in the ON position on pairs JP7
through JP8.
The jumper is a removable bridge that is
used to make or break continuity between two pins that
form a pair. When installed in the ON position, the jumper
is place on both pins of the pair and continuity between
the pins is established. When installed in the OFF posi-
tion, the jumper is removed or stored on a single pin and
continuity is broken. Jumper functions are as follows:
1.
JP1 – Dryer Type
Jumper JP1 is used to select the dryer type configu
-
ration. It is installed in the OFF position for External
Heated dryer configuration.
2.
JP2 – Energy Management
Jumper JP2 is installed in the ON position when
an Energy Management sensor is installed. It is
installed in the OFF position when no Energy Man-
agement sensor is installed.
3.
JP3 – Dew Point Transmitter
Jumper JP3 is installed in the ON position when a
Dew Point Transmitter is installed. It is installed in
the OFF position when no Dew Point Transmitter is
installed.
NOTE:
“Energy Management” can coexist with the
dew point transmitter option. Dryer control based
on the ENERGY MANAGEMENT or DEWPOINT
CONTROL is selected on Screen 1 of the Set Up
Mode.
If DEWPOINT CONTROL is not selected then the
dew point signal does not control the dryer cycle but
still serves a monitoring and alarm function.
4.
JP4 – Cooling Cycle
Jumper JP4 is installed in the ON position to disable
the Cooling Cycle. It is installed in the OFF position
enable a Cooling Cycle.
NOTE:
A Cooling Cycle is required on Externally
Heated Dryers.
5.
JP5 – Switching Failure
Jumper JP5 is installed in the ON position to enable
Switching Failure. The jumper is installed in the OFF
position if Switching Failure is disabled.
6.
JP6 – Common Alarm
Jumper JP6 is installed in the OFF position to en-
able both the dryer fault alarms and service alarms
to activate the common alarm. This is the default
configuration. Install jumper JP6 in the ON position
if the common alarm is to activated by a dryer fault
alarm only.
NOTE:
Jumpers JP7 and JP8 are used by the fac-
tory during final inspection to download language
text and to enable ‘factory’ set-up screens.
7.
JP7 – Download Language Text
Jumper JP7 is factory installed in the OFF position
to disable Language Text download. The jumper is
installed in the ON position to allow for language text
download due to either language corrections or new
language installation.
8.
JP8 – Set Up
Jumper JP8 is factory installed in the OFF position
to disable access to “factory” set up screens. The
jumper is installed in the ON position during final
inspection at the factory to set controller to match
customer requirements.
6.5 Operator Interface
Refer to
Figure 7 , Front Panel Overlay
for information
regarding the location and function of the LEDs, switches,
and text display.
6.5.1 Front Panel LED’s
• Power On - green
• Alarm - red
• Service / Maintenance reminder - amber
• Filters (pre, after, and pilot) service / maintenance
reminders - amber
• Inlet switching and purge / repressurization valve sta
-
tus (On = valve open; Off = valve closed) - green
• Left and right tower status (heating) - amber
• Left and right tower status (drying) - green
• Left and right tower pressure switch status (On =
switch closed; Off = switch open) - green
6.5.2 Front Panel Switches
The front panel contains four momentary-contact push-
button switches. Refer to Figure 7, Front Panel Overlay
for the appropriate icon associated with each switch.
Pushing on the overlay icon actuates the switch.
Data Display Switch
This switch is used to step through the display screens.
Select Switch
This button is located to the left of the text display window.
Refer to the Front Panel Operation Section for additional
information.
ENTER Switch
This button is located to the right of the text display
window. Refer to the Front Panel Operation Section for
additional information.
Alarm Reset Switch
This button is normally used to reset an alarm or service
reminder. Refer to the Front Panel Operation Section
for additional information.
