background image

Water Treatment Systems

Service Kit Manual

DRISTEEM GTS

®

 HUMIDIFIFIER, STANDARD WATER

 WARNING

Indicates a hazardous situation that could result in death or 
serious injury if instructions are not followed.

 CAUTION

Indicates a hazardous situation that could result in damage to 
or destruction of property if instructions are not followed.

mc_051508_1145

Parts in this service kit are for the GTS04 humidifi er (October 2004 to present). Parts are listed on page 2.

 WARNING

Read all warnings and instructions

This page provides important safety instructions; it is intended to supplement — not replace — the humidifi er's Installation, 
Operation, and Maintenance Manual (IOM). Read the IOM that was provided with the humidifi er before performing 
service or maintenance procedures on any part of the system. Failure to follow all warnings and instructions could 
produce the hazardous situations described here and in the IOM, resulting in property damage, personal injury, or 
death. 

If the IOM is missing, go to www.dristeem.com to download a replacement. 

Hot surfaces and hot water

Steam humidifi cation systems have extremely hot surfaces, and water in tanks, electrode cylinders, steam pipes, and 
dispersion assemblies can be as hot as 212 °F (100 °C). To avoid severe burns, allow the entire humidifi cation system to 
cool. 

Follow the cool-down procedure in the humidifi er's IOM before performing service or maintenance procedures on any 
part of the system.
 

Carbon monoxide, fi re, explosion, and electrical shock hazards

Improper installation, adjustment, alteration, service, maintenance, or use can cause carbon monoxide poisoning, fi re, 
explosion, electrical shock, and other hazardous conditions. These hazardous conditions could cause personal injury, 
property damage, or death. To prevent hazardous conditions, read all warnings; lock all power disconnect switches in 
the OFF position before removing any access panels; and consult a qualifi ed installer, service agency, local gas supplier, 
or your distributor or branch for information or assistance. The qualifi ed installer or agency must use only factory 
authorized and listed kits or accessories when modifying this product. 

If you smell gas:

•  Do not try to light any appliance.

•  Do not touch any electrical switch; do not use any phone in your building.

•  Immediately call your gas supplier from an off-site phone. Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fi re department. 

Electrical shock hazard

If the humidifi er starts up at a call for humidity during maintenance, severe bodily injury or death from electrical shock 
could occur. To prevent such start-up, follow the procedure below before performing service or maintenance procedures 
on this humidifi er (after the tank has cooled down and drained):

1. Use the Vapor-logic

®

 keypad to change the control mode to Standby. 

2.  Shut off all electrical power to the humidifi er using the fi eld-installed fused disconnect, and lock all power disconnect 

switches in the OFF position.

3. Close the fi eld-installed manual water supply and gas shut-off valves. 

Summary of Contents for GTS04



















Reviews: