Galaxy GHDX2-2430R-24F4D Installation And Hardware Reference Manual Download

Page: 60 / 129

Galaxy GHDX2-2430S/R-24F4D

Installation and Hardware Reference Manual

System

Monitoring

3-4

remain intact after default restoration, configuration data such as LUN mapping

and performance preferences will be erased. Before using this button, make sure

you have a written record or a previously saved configuration profile (one of

firmware’s functionalities, “Save NVRAM”).

Please refer to

Chapter 1

for the correct procedures of default restoration.

3.2.2

LAN Port LEDs

A shielded Ethernet cable is recommended for connecting the RJ-45 Ethernet

management port to a local network after you configure an IP address. This enables you

to manage your subsystem via LAN/WAN. Two (2) LEDs on the Ethernet port indicate

connection statuses. Please refer to

Error! Reference source not found.

for the LED

definitions.

Figure 3-2: LAN Port Indicators

Name

Color

Status

Link

Green

indicates the management port is connected to a

node or networking device.

Activity

Green

BLINKING

indicates active transmission

Table 3-3: LAN Connector LED Definitions

3.2.3

LCD Keypad Panel

The LCD keypad panel comes with three (3) status-indicating LEDs, from top to bottom,

PWR

BUSY

, and

ATTEN

. The definitions of these LEDs are shown in

Table 3-5

Summary of Contents for GHDX2-2430R-24F4D


































































































































Search results

Summary of Contents for GHDX2-2430R-24F4D

Reviews:

Related manuals for GHDX2-2430R-24F4D

Brands by name

Popular brands

Galaxy GHDX2-2430R-24F4D, Installation And Hardware Reference Manual

Search results

Summary of Contents for GHDX2-2430R-24F4D

Reviews:

Related manuals for GHDX2-2430R-24F4D

Brands by name

Popular brands