background image

Galaxy Unlimited, LLC Remote Control Box Warranty 

 

This warranty is for the electrical components of the Remote Control Box which begins on the day of purchase from 
Galaxy Unlimited, LLC for a period of 1 year thereafter. During this period, Galaxy Unlimited, LLC will replace electrical 
components, without charge, for the components of the Remote Control Box, or any part or piece thereof, which 
exhibits a manufacturing defect or defect in craftsmanship. Defect is determined at the absolute and sole discretion 
of Galaxy Unlimited, LLC. 

 

To submit an acceptable claim under this limited warranty, the Original Purchaser must provide the following 
information in writing to: 

 

Galaxy Unlimited, LLC 6470 State Highway 198 
Mabank, TX 75156 

 

 

Full Name and Address 

 

Serial Number of Unit 

 

Clear and specific description of the defect 

 

Ship malfunctioning Remote Control Box to above address for confirmation/evaluation at the expense of 
the customer. 

 

Must register Control Box online. 

 

This limited warranty is valid only when such products are used under normal conditions of recommended use. This 
limited warranty does not cover replacement or repair of any part there of damaged by acts of God, abuse, accident, 
misuse,  neglect,  alteration,  repair,  disaster,  overloading,  negligence,  unauthorized  use,  improper  installation, 
improper  testing,  improper  product  selection,  failure  to  follow  maintenance  recommendations, failure to follow 
instructions or warnings, or any other case beyond the control of Galaxy Unlimited, LLC. 

 

All  warranties  implied  by  law,  including  implied  warranties  of  merchantability  and  fitness  for  a  purpose,  are 
disclaimed or, if a disclaimer is not permitted by applicable state law, are expressly limited to the durations of the 
coverage period set forth above. 

 

Summary of Contents for 1M2S






















Reviews: