Elnur
powered by Gabarrón | INGENIUM WIFI Thermal Radiators | Installation Guide
9
4. Remote Operation using the Wifi G-Control Hub
It is possible to control the full operation of the unit remotely with Elnur Gabarron App or Web-App. The unit must be
connected to a Wifi G-Control Hub connected to the internet to use this feature.
4.1
To associate the unit to the G-Control Hub, the
discovery mode of the hub must be activated. Press
the associate button at the back of the Gateway
for 3 seconds. An orange blinking light every second
indicates association mode.
4.2
With the hub in discovery mode, press the Ok/Mode
button on the heater for 3 seconds until the Link symbol
is shown.
7
Parameters
-
C1. Fahrenheit or Celsius Degrees.
The LCD displays the temperature unit selected: ºC or ºF.
-
C2. Control Adjustment.
The kind of temperature control can be modified with this parameter:
•
PID, Hysteresis 0,25ºC, Hysteresis 0,35ºC, Hysteresis 0,50ºC, Hysteresis 0,75ºC.
-
C3. Correction of ambient temperature measures.
If there is a difference between an external thermometer and the temperature displayed by the unit, with C3
parameter it is possible to influence on the sensor in order to balance the difference. (-3ºC to +3ºC in 0,1 steps).
-
C4. Firmware version.
Information about the current firmware version of the unit.
-
C5. Open Window Activation
ON/OFF. With the parameter in ON, the open window detection is activated.
-
C6. Adaptive Start Control
ON/OFF. With the parameter in ON, the adaptive start control is activated.
4.- REMOTE OPERATION USING THE WIFI G-CONTROL HUB
It is possible to control the full operation of the unit remotely with Gabarron-Elnur app or app-web. The unit must be
connected to a Wifi G-Control Hub connected to the internet to use this feature.
4.1 To associate the unit to the G-Control Hub, the
discovery mode of the hub must be activated. Press the
associate button at the back of the Gateway for 3 seconds. An
orange blinking light every second indicates association mode.
4.2 With the hub in discovery mode, press the
Ok/Mode
button on the heater for 3 seconds until the Link symbol is
shown.
You can now control and adjust the programming and temperatures on the heater via the Gabarron-Elnur app.
4.3 To disassociate the unit, a reset of the unit must be realized. See “5. UNIT RESET”. When the heater is reset, it will
remove the programming and revert back to the default settings and also disassociate from the RF network and G-Control Hub.
5.- UNIT RESET
The heater reset removes the programming and disassociates the device from the RF network if the unit was associated with a
G-Control Hub. Default values are established. To reset the unit, hold the
OK/Mode and Config/Prog buttons simultaneously
for 10 seconds, the display will show the following to indicate the heater has been reset.
To confirm the reset of the unit, press
OK/Mode button, to cancel it any other button can be pressed.
7
Parameters
-
C1. Fahrenheit or Celsius Degrees.
The LCD displays the temperature unit selected: ºC or ºF.
-
C2. Control Adjustment.
The kind of temperature control can be modified with this parameter:
•
PID, Hysteresis 0,25ºC, Hysteresis 0,35ºC, Hysteresis 0,50ºC, Hysteresis 0,75ºC.
-
C3. Correction of ambient temperature measures.
If there is a difference between an external thermometer and the temperature displayed by the unit, with C3
parameter it is possible to influence on the sensor in order to balance the difference. (-3ºC to +3ºC in 0,1 steps).
-
C4. Firmware version.
Information about the current firmware version of the unit.
-
C5. Open Window Activation
ON/OFF. With the parameter in ON, the open window detection is activated.
-
C6. Adaptive Start Control
ON/OFF. With the parameter in ON, the adaptive start control is activated.
4.- REMOTE OPERATION USING THE WIFI G-CONTROL HUB
It is possible to control the full operation of the unit remotely with Gabarron-Elnur app or app-web. The unit must be
connected to a Wifi G-Control Hub connected to the internet to use this feature.
4.1 To associate the unit to the G-Control Hub, the
discovery mode of the hub must be activated. Press the
associate button at the back of the Gateway for 3 seconds. An
orange blinking light every second indicates association mode.
4.2 With the hub in discovery mode, press the
Ok/Mode
button on the heater for 3 seconds until the Link symbol is
shown.
You can now control and adjust the programming and temperatures on the heater via the Gabarron-Elnur app.
4.3 To disassociate the unit, a reset of the unit must be realized. See “5. UNIT RESET”. When the heater is reset, it will
remove the programming and revert back to the default settings and also disassociate from the RF network and G-Control Hub.
5.- UNIT RESET
The heater reset removes the programming and disassociates the device from the RF network if the unit was associated with a
G-Control Hub. Default values are established. To reset the unit, hold the
OK/Mode and Config/Prog buttons simultaneously
for 10 seconds, the display will show the following to indicate the heater has been reset.
To confirm the reset of the unit, press
OK/Mode button, to cancel it any other button can be pressed.
You can now control and adjust the programming and temperatures on the heater via the Elnur Gabarron app.
4.3
To disassociate the unit, a reset of the unit must be completed. See “5. UNIT RESET”. When the heater is reset,
it will remove the programming and revert back to the default settings and also disassociate from the RF network
and G-Control Hub.
5. Unit Reset
The heater reset removes the programming and disassociates the device from the RF network if the unit was
associated with a G-Control Hub. Default values are established. To reset the unit, hold the OK/Mode and
Config/Prog buttons simultaneously for 10 seconds, the display will show the following to indicate the heater
has been reset.
0:00
21.0C
AUTO
Pro
AUTO
rES
To confirm the reset of the unit, press
OK/Mod
e button,
to cancel it any other button can be pressed.
