3
Transmitter: T6EXHP
T6EXHP Transmitter with 6-model memory.
Transmitting on 35, 40, 41, or 72 MHz band.
Operating system: 2-stick, 6-channel system
Modulation: FM(PPM) and PCM
Power supply: 9.6V NT8S600B Ni-Cd battery or 12V alkaline
battery
Current drain: 250mA
Receiver: R136F
R136F narrow band, FM 6 channel receiver.
Receiving on 35, 40, 41, or 72 MHz band.
Type: FM, Single conversion
Intermediate frequencies: 455kHz, 10.7MHz/455kHz
Power requirement: 4.8V or 6V
Current drain: 9.5mA @ 4.8V
Size: R136F- 1.31x1.98x0.71” (33.4x50.3x18.1mm)
Weight: 0.98oz (27.8g)
Receiver: R127DF
R127DF narrow band, FM 7 channel receiver.
Receiving on 35, 40, 41, or 72 MHz band.
Type: FM, Dual conversion
Intermediate frequencies: 455kHz, 10.7MHz/455kHz
Power requirement: 4.8V or 6V
Current drain: 9.5mA @ 4.8V
Size: 1.39x2.52x0.82” (35.3x64.0x20.8mm)/
Weight: R127DF- 1.5oz (42.5g) / R136F- 0.98oz (27.8g)
Receiver: R138DP
R138DP narrow band, PCM 8 channel receiver.
Receiving on 35, 40, 41, or 72 MHz band.
Type: PCM, Dual conversion
Intermediate frequencies: 455kHz, 10.7MHz/455kHz
Power requirement: 4.8V or 6V
Current drain: 16mA @ 4.8V
Size: 2.56x1.42x0.85” (65.0x36.0x21.5mm)
Weight: 1.42oz (40.3g)
CONTENTS AND SPECIFICATIONS
Servos: S3001
S3001 standard ball bearing
Control system: Pulse width control,1.52ms neutral
Power requirement: 4.8 or 6V (from receiver)
Output torque: 44.4oz-in [3.2kg-cm] @4.8V
Operating speed: 0.23sec/60°@4.8V
Size: 1.59x0.78x1.41” [40.4x19.8x36mm]
Weight: S3004- 1.3oz (37.2g) / S3003- 1.3oz (38.0g)
Servos: S3151
S3151 Digital standard servo with mounting hardware and
servo arm assortment
Control system: Pulse width control,1.52ms neutral
Power requirement: 4.8 (from receiver)
Output torque: 43.1oz-in [3.1kg-cm] @4.8V
Operating speed: 0.21sec/60°@4.8V
Size: 1.59x0.79x1.42” [40.5x20x36.1mm]
Weight: 1.48oz (42g)
Other components:
Switch harness
Instruction manual
*Specifications and ratings are subject to change without notice
Receiver crystals:
The receiver frequency may be changed as long as it remains within the “low” and “high” band frequency range. If your
receiver is on any channel from 11 through 35, it is a “low band” receiver and the frequency may be changed to any other
channel from 11 through 35 without having to perform any other service. Simply purchase a crystal on the desired channel,
then replace the existing crystal in your receiver with the new one. If your receiver is on any channel from 36 through 60, it is a
“high band” receiver and the frequency may be changed to any other channel from 36 through 60. To order a receiver crystal,
replace the “**” in the order numbers below with the required channel number. (To order a receiver crystal on channel 30,
order FUTL5730.)
FM Dual Conversion 72 MHz
low band
(channels 11 - 35) receiver crystal . FUTL57**
FM Dual Conversion 72 MHz
high band
(channels 36 - 60) receiver crystal . FUTL58**
Note
: Should you ever wish to change the transmitter frequency, the transmitter must be sent to the Futaba Service Center for retuning.
