87
<Functions of Linkage Menu>
Mixing rate setting procedure
The HR3 swash-plate type will be used as an
example to describe mixing rate setting. The mixing
used in other swash modes may be different,
however, the setting procedure is the same.
*Set the throttle stick to the preset neutral point. Adjust the
length of the linkage rod so that the swash plate is horizontal
at this position.
*The sub-trim function can be used to make small
adjustments.
*Adjust so that the pitch curve is a straight line and the
helicopter achieves maximum pitch.
*Move the cursor to the item you want to adjust and touch
the RTN button to switch to the data input mode. Touch
the RTN button to end adjustment and return to the cursor
mode.
$GMXVWLQJWKHDLOHURQRSHUDWLRQ>$,/WR3,7@
$GMXVWWKH$,/WR3,7UDWHVRWKHUHLVQRELQGLQJ
LQWKHHOHYDWRURUSLWFKPRYHPHQWZKHQWKH
DLOHURQVWLFNLVPRYHGWRWKHOHIWDQGULJKW
*Adjust by scrolling the touch sensor.
*The left and right sides can be adjusted individually.
$GMXVWLQJWKHHOHYDWRURSHUDWLRQ>(/(WR$,/@
>(/(WR3,7@
$GMXVWWKH(/(WR$,/DQG(/(WR3,7UDWHVVR
WKHUH LV QR ELQGLQJ LQ WKH DLOHURQ RU SLWFK
PRYHPHQWZKHQWKHHOHYDWRUVWLFNLVPRYHG
XSDQGGRZQ
*Adjust by scrolling the touch sensor.
*The up and down sides can be adjusted individually.
$GMXVWLQJWKHSLWFKRSHUDWLRQ>3,7WR$,/@>3,7
WR(/(@
$GMXVWWKH3,7WR$,/DQG3,7WR(/(UDWHVVR
WKDW WKH VZDVK SODWH PRYHV WR WKH OHYHO
KRUL]RQWDOSRVLWLRQZKHQWKHWKURWWOHVWLFNZDV
PRYHGWRPD[LPXPORZDQGIXOOKLJK
*Adjust by scrolling the touch sensor.
*The slow and high sides can be adjusted individually.
Linkage compensation setting procedure
*Prior to utilizing the linkage compensation settings, it is
important to adjust the mixing rate settings.
*Linkage compensation overrides interference from the
aileron operation with the elevator or elevator operation
with the aileron at collective pitch control for low pitch and
high pitch.
*When making the following setting, Move the cursor to the
item you want to set and touch the RTN button to switch
to the data input mode. Touch the RTN button to end
adjustment and return to the cursor mode.
&RPSHQVDWLQJDLOHURQLQSXW>$,/@
6HWWKHWKURWWOHWRWKHORZHVWSRVLWLRQ0RYH
WKH DLOHURQ VWLFN WR WKH OHIW DQG ULJKW DQG
DGMXVW WKH DLOHURQ FRPSHQVDWLRQ DPRXQW
VRWKDWLQWHUIHUHQFHLQWKHHOHYDWRURUSLWFK
GLUHFWLRQLVPLQLPDO
*Adjust by scrolling the touch sensor.
*The left and right sides can be adjusted individually.
*If the interference increases when the compensation amount
was increased, make adjustments with the direction [DIR.]
using the plus "+" or minus "-".
&RPSHQVDWLQJHOHYDWRULQSXW>(/(@
$GMXVWWKHHOHYDWRUFRPSHQVDWLRQDPRXQW
VR WKDW WKH DLOHURQ RU SLWFK GLUHFWLRQ
LQWHUIHUHQFH ZKHQ WKH HOHYDWRU VWLFN ZDV
PRYHGXSDQGGRZQLVPLQLPDO
5HSHDWVWHSVDQGDERYHSHUIRUPDLOHURQ
DQGHOHYDWRUFRPSHQVDWLRQVLPLODUO\DWIXOO
WKURWWOH
Speed compensation setting procedure
0RYH WKH FXUVRU WR WKH 63((' LWHP DQG
WRXFKWKH571EXWWRQWRVZLWFKWRWKHGDWD
LQSXWPRGH
6HW WKH WKURWWOH VWLFN WR WKH QHXWUDO SRLQW
SRVLWLRQ4XLFNO\PRYHWKHHOHYDWRUVWLFNDQG
DGMXVW WKH VSHHG FRPSHQVDWLRQ DPRXQW
>63(('@IRUPLQLPXPLQWHUIHUHQFHLQWKHSLWFK
GLUHFWLRQ
*Adjust by scrolling the touch sensor.
7RXFKWKH571EXWWRQWRHQGDGMXVWPHQWDQG
UHWXUQWRWKHFXUVRUPRGH