background image

16

3.Press 

T

 to select the item to set and then press the 

ENTER

 key.

4.Press 

T

 or 

S

 to select an appropriate one and then press the 

ENTER

 key.

Description for each item of the NMEA menu

NMEA0183:

 Choose NMEA0183 version of navigation equipment connected to the NMEA port, 

among Ver. 1.5, Ver. 2.0 or Ver. 3.0. "SPECIAL" is for use with a navigator whose baud rate is 
600 bps.

NMEA Port:

 The NMEA terminals in the NMEA port can function as input ports or input/output 

port. Change the setting to "In/In" when connecting GP-310B/320B/330B and a wind sensor. 
When connecting the GP-320B/330B and a wind sensor, first turn on "WAAS Setup" and then se-
lect "In/In" as the NMEA Port setting. 

• In/Out: NMEA port J2 #1 & #2 is output port and J2 #3 & #4 is input port.
• In/In: NMEA port J2 #1 & #2 changes to input port. (Available with connection of the GP-310B/

320B/330B and a wind sensor.)

NMEA Output:

 Set the output data sentences.

• Off: Outputs the "output data sentences" created in the FCV-295 (see page 8).
• On: Outputs the "output data sentences" of FCV-295 and sentences which are input from other 

equipment.

WAAS Setup:

 Choose how to use the WAAS signal when connecting with a WAAS capable GPS 

receiver, for example GP-320B/330B. The message types (WAAS-00 to WAAS-27) are used as 
WAAS correction. Choose WAAS-00 to enable WAAS.

TLL Output: 

Output the position selected by the 

MARK

 key to the plotter connected.

• Off: Does not output latitude/longitude.
• TLL: Outputs latitude/longitude.
• FURUNO-TLL: Outputs latitude/longitude, depth and water temperature. This requires 

FURUNO-TLL enabled device.

Port Monitor:

 Port Monitor provides information for the data sentences input from the NMEA port. 

Press the 

ENTER

 key to display the latest data sentence information. To display this information 

on the Port 2 screen when two sensors are connected, set NMEA Port on the NMEA menu to In/
In. To terminate the port monitor, select "Exit" and press the 

ENTER

 key. And then, select Yes and 

press the 

ENTER

 key.

Summary of Contents for FCV-295









































Reviews: