background image

FURUNO Worldwide Warranty for Pleasure Boats (Except North America) 

 

This warranty is valid for products manufactured by Furuno 
Electric Co. (hereafter FURUNO) and installed on a pleasure 
boat. Any web based purchases that are imported into other 
countries by anyone other than a FURUNO certified dealer may 
not comply with local standards. FURUNO strongly recommends 
against importing these products from international websites as 
the imported product may not work correctly and may interfere 
with other electronic devices. The imported product may also be 
in breach of the local laws and mandated technical requirements. 
Products imported into other countries as described previously 
shall not be eligible for local warranty service. 
 
For products purchased outside of your country please contact 
the national distributor of Furuno products in the country where 
purchased. 
 
This warranty is in addition to the customer´s statutory legal 
rights. 
 

1. Terms and Conditions of Warranty 

 

FURUNO guarantees that each new FURUNO product is the 
result of quality materials and workmanship. The warranty is 
valid for a period of 2 years (24 months) from the date of the 
invoice, or the date of commissioning of the product by the 
installing certified dealer.   
 
 

2. FURUNO Standard Warranty 

 
The FURUNO standard warranty covers spare parts and labour 
costs associated with a warranty claim, provided that the product 
is returned to a FURUNO national distributor by prepaid carrier. 
 
The FURUNO standard warranty includes: 
 

 

Repair at a FURUNO national distributor 

 

All spare parts for the repair   

 

Cost for economical shipment to customer 

 

3. FURUNO Onboard Warranty 

 
If the product was installed/commissioned and registered by a 
certified FURUNO dealer, the customer has the right to the 
onboard warranty.   
 
The FURUNO onboard warranty includes 
 

• 

Free shipping of the necessary parts   

• 

Labour: Normal working hours only 

• 

Travel time: Up to a maximum of two (2) hours 

• 

Travel distance: Up to a maximum of one hundred 
and sixty (160) KM by car for the complete journey 

 

4. Warranty Registration 

 
For the Standard Warranty - presentation of product with serial 
number (8 digits serial number, 1234-5678) is sufficient. 
Otherwise, the invoice with serial number, name and stamp of 
the dealer and date of purchase is shown. 
 
For the Onboard Warranty your FURUNO certified dealer will 
take care of all registrations.   
 

5. Warranty Claims 

 
For the Standard Warranty - simply send the defective product 
together with the invoice to a FURUNO national distributor.   
For the Onboard Warranty – contact a FURUNO national 
distributor or a certified dealer. Give the product´s serial number 
and describe the problem as accurately as possible. 

Warranty repairs carried out by companies/persons other than a 
FURUNO national distributor or a certified dealer is not covered 
by this warranty. 
 

6. Warranty Limitations 

 

When a claim is made, FURUNO has a right to choose whether 
to repair the product or replace it. 
 
The FURUNO warranty is only valid if the product was correctly 
installed and used. Therefore, it is necessary for the customer to 
comply with the instructions in the handbook. Problems which 
result from not complying with the instruction manual are not 
covered by the warranty. 
 
FURUNO is not liable for any damage caused to the vessel by 
using a FURUNO product. 
 
The following are excluded from this warranty: 

 

a. Second-hand 

product 

 
b. 

Underwater unit such as transducer and hull unit 

 

c. 

Routine maintenance, alignment and calibration 
services. 

 

d. 

Replacement of consumable parts such as fuses, 
lamps, recording papers, drive belts, cables, protective 
covers and batteries. 

 

e. 

Magnetron and MIC with more than 1000 transmitting 
hours or older than 12 months, whichever comes first. 

 
f. 

Costs associated with the replacement of a transducer 
(e.g. Crane, docking or diver etc.). 

 
g. 

Sea trial, test and evaluation or other demonstrations. 

 
h. 

Products repaired or altered by anyone other than the 
FURUNO national distributor or an authorized dealer. 

 
i. 

Products on which the serial number is altered, 
defaced or removed. 

 
j. 

Problems resulting from an accident, negligence, 
misuse, improper installation, vandalism or water 
penetration. 

 
k. 

Damage resulting from a force majeure or other natural 
catastrophe or calamity. 

 
l. 

Damage from shipping or transit. 

 
m. 

Software updates, except when deemed necessary 
and warrantable by FURUNO. 

 
n. 

Overtime, extra labour outside of normal hours such as 
weekend/holiday, and travel costs above the 160 KM 
allowance 

 
o. 

Operator familiarization and orientation. 

 
 
 
FURUNO Electric Company, March 1, 2011 

Summary of Contents for DFF1-UHD









































Reviews: