English
5
Accessories Sold Separately
Wheel Kit
(C-FCR00DCAPA-01)
Furrion ePod
TM
Battery
(FBN12C33A1)
Solar Panel
(FSPK10MWN-BL)
NOTE:
For the wheel kit, Furrion ePod
TM
battery and solar
panel, please refer
to their own manuals separately for
instructions.
Shared ECO System Components
ePod
TM
Battery
Provided with the ePod
TM
, sold separately with the
eRove
TM
cooler.
Solar Panel
Sold separately for both the eRove
TM
cooler and the
ePod
TM
, but can be shared.
DC (Cigarette Lighter) Plug & AC/DC Adapter
Shared between both the eRove
TM
cooler and the ePod
TM
,
and provided with each.
ePod
TM
Battery
DC (Cigarette Lighter) Plug
AC/DC Adapter
Solar Panel
(FSPK10MWT-BL)
Furrion eRove™
FCR45DCAPA-GL
Furrion Powerstation
™
FIVSPB40A-BL
ePod
TM
Battery
Installation
NOTE: 12V Wiring Installation
●
Provide a dedicated circuit to prevent light flicker and
other 12V appliance interference.
●
Ensure proper wire gauges are used per the following:
AWG Gauge
Max Length* 12V DC
(ft.) (m)
14
0 - 6
0 - 1.8
12
6 - 10
1.8 - 3
10
10 -20
3 - 6
8
20 - 30
6 - 9.1
●
Protect circuit with a 15A delayed or slow blow fuse.
Storing & Transporting
WARNING
EXCESSIVE WEIGHT HAZARD
In case of back or other injuries
to be caused while moving the
cooler, two or more persons
should be utilized to move and
install the cooler.
●
Store the Cooler at the temperature range of
-27°F ~ 122°F (-33°C ~ 50°C).
CAUTION
Leaving loose objects inside the cooler compartments
while inside a vehicle on the move can damage the cooler
unit. Always make sure the stored objects are secured.
Location
●
This appliance is designed to be free standing only, and
should not be recessed or built in a cabinet.
●
NEVER block the air vents during operation and make
certain at least 1" (25.4mm) clearance exists to the air
vents for good circulation.
●
Ensure 20'' (508mm) of clearance is above the cooler to
open the lids for accessing the compartments if needed.
●
It is recommended to operate the unit on a flat surface, or
the surface with slope of no more than 30°.
●
The unit must be placed in a dry and ventilated place far
away from heat sources (such as stove, flue), place the
unit in a well shaded area. (Prevent exposure to direct
sunlight.)
●
When the cooler is attached on the prep kit, make sure
there is 20'' (508mm) of clearance on top of the cooler so
that its lids can be opened without blocking.
Wiring
The cooler can be powered from the following auxiliary
sources:
1. Via power adaptor, plugged into a standard fused NEMA
5-15R AC outlet (GFCI not required, as the cooler only
uses a NEMA 1-15P plug, which has no protective ground
terminal). Ensure the outlet can provide at least 3A of
current. The power adaptor is only to be used indoors.
2. Via by-packed cigarette lighter harness, plugged into
a standard 12V cigarette outlet. Ensure the outlet can
provide a continuous current of 10A, with short peaks up
to 15A. The outlet shall be fused as per applicable local
legislation.
