FunkTronic Major 4 Manual Download Page 13

m4_eng(11.03.02)

- 13 -

Kompetent für Elektroniksysteme

tone Sequence whereby tone 'A' is also accepted. In case of successful decoding the loudspeaker 

and the handset are switched on, the loudspeaker lamp ashes, and the bell tone is started. An 

acknowledgement is not transmitted.

Emergency Call Decoder

The emergency call decoder is coded in register 004 (EEPROM 1). If this decoder is not required, 

please code an 'F' at the rst digit of the tone sequence. The read in 5-tone sequence is compared 

with the emergency coding. From the second up to the fth digit those positions being coded with 

'F' will accept all tones of the tone system. In case of successful decoding the loudspeaker and 

the handset are switched on, the loudspeaker lamp ashes, and a time window with a duration of 

three seconds is opened. The rst tone sequence to be received within the time window closes the 

time window, and is then stored as emergency call, and ashes on the right display. As long as an 

emergency call is indicated on the display, the keypad is blocked with exception of the PTT button and 

the 'F1' key. The emergency call number can be deleted only with the 'F1' key.

Conference Call Decoder

The  conference  call  decoder  detects  a  tone  of  at  least  one  second  duration. After  detection  the 

loudspeaker and the handset are switched on, the loudspeaker lamp ashes, and the bell tone is 

activated. No acknowledgement is transmitted. The conference call tone frequency is coded at digit 

2 of register 046 (EEPROM 1) with the corresponding digit of the tone system ('0' ... 'E') . If this 

decoder is not required, please code an 'F' at that digit.

ID-Code Memory

Function

The  ID-code  memory  can  be  congured  so  that  it  is  optimally  adapted  to  current  use.  Up  to  16 

ID-codes can be stored. If all memory positions are engaged, the memory is updated by deleting the 

oldest ID-code. The stored ID-codes can be scrolled through by pressing the (M) key in such way 

that the ID-code stored last is displayed by the rst key pressing. The currently displayed ID-code 

can be deleted from the memory by pressing the (*) key. If the "FIFO" function is switched on, always 

the  oldest  number  is  shown  on  the  display  by  pressing  the  (M)  key,  and  only  after  deleting  this 

ID-code the next ID-code follows. The "FIFO" function is programmed at the rst digit of register 033 

in EEPROM 1 ('0' = off, '1' = on). The ID-code memory can be used for single or double sequences. 

In  case  of  double  sequences  the  rst  or  the  second  tone  sequence  is  stored  according  to  the 

"ID-Mode" switch. The "ID-Mode" is programmed at digit 3 of register 033 in EEPROM 1 ('0' = 2nd 

tone sequence, '1' = 1st tone sequence). The storing of an ID-code can be signalled by a beep tone 

which can be programmed at digit 2 of register 033 in EEPROM 1 ('0' = off, '1' = on). The ID-code 

memory can also be used as call-back memory. In order to avoid acknowledgement sequences to 

get into the memory, the ID-code memory can be blocked for n * 100 ms after every call transmission. 

The blocking time is programmed at digit 2 of register 041 (EEPROM 1).

Monitor

If every ID-code has to be stored, digit 3 of register 021 (EEPROM 1) has to be programmed with 

a '1'. Now every ID-code is compared with the key tones and, if the test is positive, it is transferred 

to the ID-code memory. But if the system is operating with double sequences, the monitor switch 

must remain in "off" position ('0').

Summary of Contents for Major 4
































Reviews: