Fukuda Denshi LX-7120 Operation Manual Download Page 26 | Manualshive

Page: 26 / 74

background image

3. Preparation

6

Lift the lock lever to open the battery
compartment lid as shown in the left picture.

Install new battery according to the polarity
indication inside the battery compartment.
Make sure to first Insert the battery into the
battery compartment from the minus (-)
terminal as shown in the left picture.

Hook the lock lever on the projection from
the body and press it down until it is
horizontal (flat position).

CAUTION



Make sure that any foreign particles, such as hairs, are not held on

the battery compartment lid and dust is not adhered to the edge of the
lid to prevent water entering into the battery compartment area.



Make sure to only turn ON the LX-7120 after closing the battery

compartment lid.

«
...
24
25
26
27
28
...
»

Summary of Contents for LX-7120











































































Reviews:

No comments

Related manuals for LX-7120

Brand: ABBA Pages: 8

Brand: RadioMaster Pages: 3

COOPER POWER SERIES

Brand: Eaton Pages: 24

COOPER POWER SERIES

Brand: Eaton Pages: 32

Brand: Casablanca Pages: 10

Brand: Invisible systems Pages: 15

Brand: GUILCOR Pages: 7

Brand: Yaesu Pages: 3

Brand: Black Widow Security Pages: 2

TEK-W AVE 4300C

Brand: TEKTROL Pages: 35

Brand: Me Pages: 50

Brand: Lafayette Pages: 26

Brand: Gonset Pages: 23

Brand: Team Blacksheep Pages: 14

Brand: C4Line Pages: 2

Brand: Yaesu Pages: 34

Brand: RoboGuard Pages: 8

Brand: Kongsberg Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands