Fukuda Denshi LX-7120 Operation Manual Download Page 13 | Manualshive

Page: 13 / 74

background image

Electromagnetic Compatibility

The performance of this device under electromagnetic environment complies
with IEC 60601-1-2 (2007).

Precautions for Safe Operation under Electromagnetic Influence

CAUTION

If any sorts of electromagnetic wave, magnetic field, or static electricity
exist around the device, noise interference or malfunction of the device
may occur. If any unintended malfunction or noise occurs during
monitoring, check the magnetic influence and take appropriate
countermeasures.
The following are examples of the common cause and countermeasures.

●

Cellular Phone

The radio wave may cause malfunction to the device.
Cellular phones and radio sets should be turned off in the room
(building) where medical device is located.

●

Static Electricity

In a dry environment (room), static electricity is likely to occur. Take
the following countermeasures.



Both operator and patient should remove any static electricity before

entering the room.



Humidify the room.

xi

«
...
11
12
13
14
15
...
»

Summary of Contents for LX-7120











































































Reviews:

No comments

Related manuals for LX-7120

MAGNETIC PRO YSH

Brand: YOODA Pages: 2

Brand: CAME-TV Pages: 4

Brand: Lafayette Pages: 22

Brand: Vaisala Pages: 64

Gossen MetraWatt SINEAX DME 401

Brand: Camille Bauer Pages: 36

Brand: Mighty Module Pages: 2

Brand: Narco Avionics Pages: 16

Brand: tams elektronik Pages: 12

Brand: Climax Technology Pages: 4

Brand: Xantrex Pages: 76

Brand: XIEGU Pages: 4

Brand: WIKA Pages: 64

VXA-300 Pilot III

Brand: Vertex Standard Pages: 32

Brand: Vision Pages: 9

Brand: Peavey Pages: 4

Brand: Goobay Pages: 8

SET 12-06 LED slim

Brand: Goobay Pages: 24

Brand: Advanced Microwave Products Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands