manualshive.com logo in svg

Fujitsu PRIMERGY RX2530 M1, Operating Manual, Page: 54 / 86

Share
Download
Fujitsu PRIMERGY RX2530 M1 Operating Manual Download Page 54

54

Operating Manual

 RX2530 M1

Hardware installation

5.4

Connecting the server to the mains

In its basic configuration level the server has a hot-plug power supply unit. 

A second hot-plug power supply unit can be added to ensure a redundant power 
supply. If one power supply unit is defective, the other then guarantees 
unimpaired operation. Each hot-plug power supply unit can be replaced during 
operation (see the "PRIMERGY RX2530 M1 Server Upgrade and Maintenance 
Manual").

V

CAUTION!

The PSU is automatically set to a mains voltage in the range 100 - 240 V 
(PSU Platinum) or 200 - 240 V (PSU Titanium). You may only operate the 
server if its rated voltage range corresponds to the local mains voltage.

Ê

Connect the power cord to the server power supply unit.

Ê

Connect the mains connector to an outlet on the rack's socket strip (see also 
Technical Manual for the rack).

I

A phase redundancy in the power supply of the server can be set up if 
two hot-plug power supply units are installed. 

In this case, each of the power supply units is either connected to two 
different phases or to two separate circuits of the internal power supply 
network.

Summary of Contents for PRIMERGY RX2530 M1























































































Reviews:

No comments