manualshive.com logo in svg

Fujitsu PRIMERGY RX2530 M1, Operating Manual, Page: 48 / 86

Share
Download
Fujitsu PRIMERGY RX2530 M1 Operating Manual Download Page 48

48

Operating Manual

 RX2530 M1

Hardware installation

5.1

Unpacking the server

V

CAUTION!

Follow the safety instructions in 

"Important information" on page 33

.

The server must always be lifted or carried by at least two people.
(For the Japanese market, please refer to "

安全上のご注意

".)

Do not unpack the server until it is at its installation location.

Ê

Transport the server to the place where you want to set it up.

Ê

Unpack all individual parts.

Keep the original packaging in case you want to transport the server again 
(applies only to global market).

Ê

Check the delivery for any damage during transport.

Ê

Check whether the items delivered match the details on the delivery note.

The product name and serial number of the product can be found on the ID card 
(see section 

"Front of the server" on page 59

).

Ê

Notify your supplier immediately should you discover that the items 
delivered do not correspond to the delivery note.

Summary of Contents for PRIMERGY RX2530 M1























































































Reviews:

No comments