Fujitsu PRIMERGY RX2530 M1 Operating Manual Download Page 23 | Manualshive

Page: 23 / 86

Fujitsu PRIMERGY RX2530 M1 Operating Manual Download Page 23

RX2530 M1

Operating Manual

23

Functional overview

2.2

Server specification

This section explains the specifications for the server. The specifications for this
server are liable to be updated without any notice. Please be forewarned.

System Board

Processor

Memory Modules Configuration

System board type

D3279

Chipset

Intel

®

C610

Processor quantity and
type

1or 2 Intel

®

Xeon

®

E5-2600 v3 family processors

Memory slots

24

Memory slot type

DDR4

Memory capacity
(min. - max.)

4 GB - 1536 GB

Memory protection

Memory Scrubbing; SDDC (only for registered
DIMMs); Hot-spare memory support
Memory Mirroring support; Rank sparing memory
support

Memory notes

Memory Mirroring with identical modules in both
channel pairs of a bank (4 modules per bank), Rank
sparing or Performance Mode with identical modules
in all four channels (4 modules per bank).

«
...
21
22
23
24
25
...
»

Summary of Contents for PRIMERGY RX2530 M1























































































Reviews:

No comments