Fujitsu PRIMERGY RX1330 M1 Page 61 Operating Manual Download

Page: 61 / 84

RX1330 M1

Operating Manual

Starting up and operation

6.1.1.2

Indicators on the control panel

Symbol

Indicator

Status

Description

Power-on
indicator

off

is off in the following case:

– the system is in power-off mode

but connected to the mains (AC
connected)

green on

is on in the following cases:

– the system has been switched

on and is in power-on delay

– the system is powered on and in

normal operation (S0)

flashes
slowly (1/2
Hz)

iRMC S4 is not ready

Power-off
indicator

Power-off
indicator (AC
connected)

green on

is on in the following cases:
– the system is in power-off mode

but connected to the mains (AC
connected)

– the system has been switched

on and is in power-on delay

After connecting the server
to the mains it takes about
60 seconds until the server
enters the standby mode.

off

is off in the following cases:
– the system is not connected to

the mains

– the system is powered on and in

normal operation (S0)

HDD / SSD
activity
indicator

green
flashing

Data access in progress

Summary of Contents for PRIMERGY RX1330 M1





















































































Search results

Summary of Contents for PRIMERGY RX1330 M1

Reviews:

Related manuals for PRIMERGY RX1330 M1

Brands by name

Popular brands

Fujitsu PRIMERGY RX1330 M1, Operating Manual

Search results

Summary of Contents for PRIMERGY RX1330 M1

Reviews:

Related manuals for PRIMERGY RX1330 M1

Brands by name

Popular brands