Fujitsu PRIMERGY RX1330 M1 Page 57 Operating Manual Download

Page: 57 / 84

RX1330 M1

Operating Manual

Hardware installation

5.5

Notes on connecting/disconnecting cables

CAUTION!

Always read the documentation supplied with the device you wish to
connect.

Never connect, or disconnect cables during a thunderstorm.

Never pull on a cable when disconnecting it. Always take hold of the
cable by the plug.

Follow the sequence described below to connect or disconnect external
devices to or from the server:

Be sure to wait for 10 seconds or more after shutdown before turning the
server on.

Connecting cables

Turn off all power and equipment switches.

Disconnect all power plugs from the properly grounded power outlets.

Connect all cables to the server and peripherals.

Plug all data communication cables into the utility sockets.

Plug all power cords into the properly grounded power outlets.

Disconnecting cables

Turn off all power and equipment switches.

Disconnect all power plugs from the properly grounded power outlets.

Unplug all data communication cables from the utility sockets.

Disconnect the relevant cables from the server and all the peripherals.

For connecting or disconnecting LAN cables, the server does not need
to be powered off. To avoid loss of data teaming function has to be
enabled.

Summary of Contents for PRIMERGY RX1330 M1





















































































Search results

Summary of Contents for PRIMERGY RX1330 M1

Reviews:

Related manuals for PRIMERGY RX1330 M1

Brands by name

Popular brands

Fujitsu PRIMERGY RX1330 M1, Operating Manual

Search results

Summary of Contents for PRIMERGY RX1330 M1

Reviews:

Related manuals for PRIMERGY RX1330 M1

Brands by name

Popular brands