manualshive.com logo in svg

Fujitsu MHN2100AT - Mobile 10 GB Hard Drive, Product Manual

Introducing the Fujitsu MHN2100AT - Mobile 10 GB Hard Drive! Need a user manual to discover all its amazing features? Look no further! Download the free product manual from manualshive.com and unlock the full potential of this high-performance hard drive. Get your hands on it now and elevate your storage experience!

Share
Download
background image

5.1  Physical Interface

C141-E120-02EN

5-5

[signal]

[I/O]

[Description]

CS0-

I

Chip select signal decoded from the host address bus.  This signal
is used by the host to select the command block registers.

CS1-

I

Chip select signal decoded from the host address bus.  This signal
is used by the host to select the control block registers.

DA 0-2

I

Binary decoded address signals asserted by the host to access task
file registers.

KEY

-

Key pin for prevention of erroneous connector insertion

PDIAG-

I/O

This signal is an input mode for the master device and an output
mode for the slave device in a daisy chain configuration. This
signal indicates that the slave device has been completed self
diagnostics.

This signal is pulled up to +5 V through 10 k

Ω

 resistor at each device.

CBLID-

I/O

This signal is used to detect the type of cable installed in the
system.

This signal is pulled up to +5 V through 10 k

Ω

 resistor at each device.

DASP-

I/O

This is a time-multiplexed signal that indicates that the device is
active and a slave device is present.

This signal is pulled up to +5 V through 10 k

Ω 

resistor at each device.

IORDY

O

This signal requests the host system to delay the transfer cycle
when the device is not ready to respond to a data transfer request
from the host system.

DDMARDY
-

O

Flow control signal for Ultra DMA data Out transfer (WRITE
DMA command).  This signal is asserted by the device to inform
the host that the device is ready to receive the Ultra DMA data
Out transfer.  The device can negate the DDMARDY- signal to
suspend the Ultra DMA data Out transfer.

DSTROBE

O

Data In Strobe signal from the device during Ultra DMA data In

transfer.  Both the rising and falling edges of the DSTROBE
signal latch data from Data 15-0 into the host.  The device can
suspend the inversion of the DSTROBE signal to suspend the
Ultra DMA data In transfer.

CSEL

I

This signal to configure the device as a master or a slave device.

−

 

When CSEL signal is grounded, the IDD is a master device.

−

 

When CSEL signal is open, the IDD is a slave device.

This signal is pulled up with 240 k

Ω

 resistor at each device.

DMACK-

I

The host system asserts this signal as a response that the host
system receive data or to indicate that data is valid.

Summary of Contents for MHN2100AT - Mobile 10 GB Hard Drive













































































































































































































































Reviews:

No comments

Related manuals for MHN2100AT - Mobile 10 GB Hard Drive

NEC Express5800/R120f-2E Configuration Manual preview
Express5800/R120f-2E
Brand: NEC Pages: 36
M-system AB2 Instruction Manual preview
AB2
Brand: M-system Pages: 3
PaloAlto Networks M-300 Quick Start Manual preview
M-300
Brand: PaloAlto Networks Pages: 2
Quantum Scalar i6000 Installation Manual preview
Scalar i6000
Brand: Quantum Pages: 384
Tandberg Data DLT-V4 Product Specification preview
DLT-V4
Brand: Tandberg Data Pages: 60
Eastwood 31652 Instructions Manual preview
31652
Brand: Eastwood Pages: 8
Buffalo MiniStation HD-PF320U2 Specifications preview
MiniStation HD-PF320U2
Brand: Buffalo Pages: 2
Dancover ProShed Owner'S Manual/ Instructions For Assembly preview
ProShed
Brand: Dancover Pages: 30
Surveon EonServ 5000 Series User Manual preview
EonServ 5000 Series
Brand: Surveon Pages: 33
Seagate ST31230N/ND Installation Manual preview
ST31230N/ND
Brand: Seagate Pages: 36
Jimmy at work SPR10004 Owner'S Manual preview
SPR10004
Brand: Jimmy at work Pages: 25
Glyph DV-Project Specification preview
DV-Project
Brand: Glyph Pages: 2
IBM 9835-415 Deployment Manual preview
9835-415
Brand: IBM Pages: 126
Storageflex NAS RAID 3945N Manual preview
NAS RAID 3945N
Brand: Storageflex Pages: 134
Qualstar HP9000 Quick Start Manual preview
HP9000
Brand: Qualstar Pages: 8
HPE StoreVirtual 3200 Installation Manual preview
StoreVirtual 3200
Brand: HPE Pages: 54
HOMEDEPOT G37007 Instruction Manual preview
G37007
Brand: HOMEDEPOT Pages: 24
Yardmaster 1013 WGY Assembly Instructions Manual preview
1013 WGY
Brand: Yardmaster Pages: 24

Brands by name

Popular brands

Load more brands