Fujitsu M304X series Oem Manual Download

Page: 104 / 143

Table 6.6 Printer status

continued

code

2 9

3 0

3 1

3 5

3 6

3 9

Printer status

NOCHNL

(Channel selected,

FCB Not

loaded)

NOCHNL

(Illegal channel)

Invalid character

code

FUSE

(Fuse 3 and

fuse

FUSE

(Fuse

Form length mode

FCB mode

load

FCB

mode

. The line feed pitch was designated as 6

lpi

Status

lines per inch

by printer setting.

lines per inch

Auto-perforation

skip enabled

tab Sel.

channel 3

Vert.

tab

channel 4

Description

printer tried to execute the Skip 'to Channel

command, but FCB

was not loaded.

printer tried to execute the Skip

Channel

command, but the specified channel number was not 1

12.

specified channel number in the load FCB

Error

data was not 1 to 12.

The printer regards it as an

error.

An invalid character code occurred.

printer

does not regard it as an error and doe:; not stop.

It is converted into

status

The forms feed fuse

The

regards

it as a" error and stops.

The hammer drive fuse was

The printer

regards it as an error and stops.

printer is in this status before

Data command is issued from the host,, or before

FCB image data is loaded by the

. The printer received load FCB

data and

the data in the FCB in the printer.

. The printer is put in this status

when the

FCB data is correct.

If not, the

code is

39.

FCB

data

loaded by

and written

in FCB.

the data is not correct, the status data is 39.

correctly receiving the

Vertical Pitch

from the host, the printer is put in the

lpi status that the host designates.

that

time, the printer does not transmit this status

code

to the host.

printer is in 6 lpi mode.

The printer is in lpi mode.

perforation skip function is enabled

VT = channel 3

VT = channel 4

6 29

Summary of Contents for M304X series
















































































































































Search results

Summary of Contents for M304X series

Reviews:

Related manuals for M304X series

Brands by name

Popular brands

Fujitsu M304X series, Oem Manual

Search results

Summary of Contents for M304X series

Reviews:

Related manuals for M304X series

Brands by name

Popular brands