Fujitsu M304X series Oem Manual Download

Page: 106 / 143

Table 6.6 Printer status

continued

code

Printer status

Monitor

line signal

detector

with

for

Description

Error/

constant ON

9 5

Reverse channel
enabled

Reverse channel
line almost
full = on

9 6

Reverse channel
enabled

Reverse channel
line almost
full = off

Transmission error

9 9

Invalid control
code

1 0 0

Invalid control

1 0 1

Buffer overflow

1 0 2

Right margin

103 Invalid

load

104 Invalid

load

Drop

with

switch mode

enabled.

status

message protocol

is enabled.

status

The message protocol Reverse Channel enabled.
When this signal is on, the interface buffer is
almost full.

message protocol Reverse

signal is

enabled.

this signal is on, the

buffer is almost empty.

status

If status

is selected, the printer

therefore, the

switch is enabled.

status

code is the same

as that of the

above status code.

This status code is the same manner as that of the

above status code.

status

interface buffer overflowed. The printer

E r r o r

abandons the data after the buffer overflows.

the right margin function is disabled, and the

received data exceeds the right margin,, the printer
reports this status.

However,

this function is

enabled, the printer prints the data which exceeds
the right margin on the next line, and does not
report this status.

Summary of Contents for M304X series
















































































































































Search results

Summary of Contents for M304X series

Reviews:

Related manuals for M304X series

Brands by name

Popular brands

Fujitsu M304X series, Oem Manual

Search results

Summary of Contents for M304X series

Reviews:

Related manuals for M304X series

Brands by name

Popular brands