background image

En-14

13.   ERROR CODES

[Troubleshooting at the remote controller LCD]

This is possible only on the wired remote controller.

[Self-diagnosis]

If an error occurs, the following display will be shown.(“Er” will appear in the set room 
temperature display.)

Error code

Unit number of indoor unit

EX. Self-diagnosis

Wired remote

controller

Error code

Description

Serial communication error

Wired remote controller communication error

Check run unfinished

Unit number or Refrigerant circuit address setting error 

 

[Simultaneous Multi]

Indoor unit capacity error

Combination error

• 

Connection unit number error (indoor secondary unit)  

[Simultaneous Multi]

• 

Connection unit number error (indoor unit or branch unit) [Flexible 

Multi]

Primary unit, secondary unit set-up error [Simultaneous Multi]

Power supply interruption error

Indoor unit PCB model information error

Manual auto switch error

Room temp. sensor error 

Indoor unit Heat Ex. Middle temp. sensor error

Indoor unit fan motor error

Drain pump error

Damper error 

Indoor unit error

Outdoor unit main PCB model information error or communication 
error
Inverter  error 

Active filter error, PFC circuit error 

Trip terminal L error

Display PCB microcomputers communication error  

Discharge temp. sensor error

Compressor temp. sensor error

Outdoor unit Heat Ex. liquid temp. sensor error

Outdoor temp. sensor error

Suction Gas temp. sensor error

• 

2-way valve temp. sensor error

• 

3-way valve temp. sensor error

Heat sink temp. sensor error

• Sub-cool Heat Ex. gas inlet temp. sensor error
• Sub-cool Heat Ex. gas outlet temp. sensor error

Liquid pipe temp. sensor error

Current sensor error

• 

Discharge pressure sensor error

• Suction pressure sensor error
• High pressure switch error

Trip detection

Compressor rotor position  
detection error (permanent stop) 
Outdoor unit fan motor 1 error

Outdoor unit fan motor 2 error

4-way valve error

Coil (expansion valve) error

Discharge temp. error

Compressor temp. error

High pressure error

Low pressure error

Branch boxes error  

[Flexible Multi]

9379123143_IM.indb   14

10/16/2017   08:55:11

Summary of Contents for ARYG LHTA 1ph
















Reviews: