En-8
REMOTE CONTROLLER INSTALLATION
11.
CAUTION
Check that the indoor unit correctly receives the signal from the remote controller,
then install the remote controller holder.
Select the remote controller holder selection site by paying careful attention to the fol-
lowing:
Avoid places in direct sunlight.
Select a place that will not be affected by the heat from a stove, etc.
Remote controller holder installation
11. 1.
!
Install the remote controller a maximum distance of 6 m from the remote control signal
receiver. However, when installing the remote controller, check that it operates cor-
rectly.
!
Install the remote controller holder to a wall, pillar, etc. with the tapping screw.
Remote controller
holder
Þ
Remote controller
mounting
Remote controller
holder
Tapping
screw
(small)
(1) Set
Remote
controller
(2) Down
OPTIONAL KIT INSTALLATION (UTY-TWBXF)
12.
This air conditioner can be connected with the following optional kits.
• Wired remote controller
• Simple remote controller
• External connect kit
BEFORE INSTALL WIRED REMOTE CONTROLLER
• When you use wired remote controller, some functions may not be used.
CAUTION
Before installing, be sure to disconnect all power supply.
Don’t touch the heat exchanger.
During installing or removing operation, be sure not to have wire catched by parts or
draw it hard. Or it may result troubles to the air-conditioner.
Avoid place in direct sunlight.
Select place that will not be affected by the heat from a stove, etc
Before setting up the optional kit, please con
Þ
rm whether air-conditioner can receive
the signal.
Do not connect the wired remote controller to the terminal for power supply.
When connecting the wired remote controller with the indoor unit, use the connecting
cable (supplied with wired remote controller or simple remote controller).
Recommended cable length of wired remote controller is 10 m. Make sure to do insu-
late of connecting part when extended the cable.
Do not connect power supply with the terminal.
INDOOR UNIT
PCB
TERMINAL
Front panel installation
9. 4.
(1) First,
Þ
t the lower part of the front panel, and insert top and bottom hooks. (2 top
sides, 7 bottom sides, 2 center)
Indoor unit
Bottom holes
(3 position)
Bottom hooks
(3 position)
Bottom holes
(4 position)
Center holes
(2 position)
Center hooks
(2 position)
Top hooks
(2 position)
Top holes
(2 position)
Indoor unit
Front panel
Bottom hooks
(2 position)
Bottom hooks
(2 position)
Front panel
(2) Attach the 4 screws.
(3) Attach the wire cover. (Attach the 1 screw.)
(4) Attach the intake grille.
CAUTION
Install the Front panel and Intake grille securely. If installation is imperfect, the Front
panel or Intake grille may fall off and cause injury.
TEST RUN
10.
Check items
(1) Is operation of each button on the remote controller unit normal?
(2) Does each lamp light normally?
(3) Do air
ß
ow direction louvers operate normally?
(4) Is the drain normal?
(5) Do not have an abnormal noise and vibration during operation?
!
Do not operate the air conditioner in test run for a long time.
[Operation method]
!
For the operation method, refer to the operating manual.
!
The outdoor unit, may not operate, depending on the room temperature. In this case,
keep on pressing the MANUAL AUTO button of the indoor unit for more than 10
seconds. The OPERATION indicator lamp (green) and TIMER indicator lamp (orange)
will begin to
ß
ash simultaneously during cooling test run. Then, heating test run will
begin in about 3 minutes when HEAT is selected by the remote control operation. (Please
follow the operating manual for remote control operation.)
(When the air conditioner is running by pressing the test run button, the OPERATION
indicator lamp and TIMER indicator lamp will simultaneously
ß
ash slowly.)
Press and hold MANUAL AUTO
button for 10 seconds
MANUAL AUTO button
!
When ending the test run, keep on pressing the MANUAL AUTO button of the indoor
unit for more than 3 seconds.
[Using the wired remote controller] (Option)
For the operation method, refer to the operating manual.
(1) Stop the air conditioner operation.
(2) Press the MODE button and the FAN button simultaneously for
2 seconds or more to start the test run.
Test run display
(3) Press the start/stop button to stop the test run.
