background image

En-13

30

Energy saving 
level setting (*1)

Level 1 (stop)

3

0

0

0

Level 2 
(operated at 40% capacity)

0

1

Level 3 
(operated at 60% capacity)

0

2

Level 4 
(operated at 80% capacity)

0

3

Level 5 
(operated at 100% capacity)

0

4

The capacity limit can be selected by the external input terminal (CN133) when 
operating with the “Energy Saving Peak Cut function”.
The lower the level, the more the effect of energy saving, but the cooling/heating 
performance will also drop.

31

Prohibited (Factory default)

3

1

0

0

40

Capacity priority 

setting (in low 

noise mode) (*1)

Off (quiet priority)

4

0

0

0

On (capacity priority)

0

1

If the cooling/heating performance becomes insufficient when the low noise mode 
is set, it is possible to set “capacity priority” that automatically cancels the low 
noise mode (once performance is restored, the mode will automatically return to 
the low noise mode).

41

Low noise mode 
setting (*1)

Off (Normal)

4

1

0

0

On (Low noise mode)

0

1

42

Low noise mode 
level setting 

Level 1

4

2

0

0

Level 2

0

1

Prohibited

0

2

52

Prohibited (Factory default) (*4)

5

2

0

0

53

Prohibited (Factory default)

5

3

0

0

60

Prohibited (Factory default)

6

0

0

0

70

Electricity meter 
No. setting 1 (*2)

Setting number (x00)

7

0

0

0

Setting number (x01)

0

1

······

···

···

Setting number (x98)

9

8

Setting number (x99)

9

9

Set the ones digit and tens digit of the No. of the electricity meter connected to 
CN135.

71

Electricity meter 
No. setting 2 (*2)

Setting number (0xx)

7

1

0

0

Setting number (1xx)

0

1

Setting number (2xx)

0

2

Set the hundreds digit of the No. of the electricity meter connected to CN135.

72

Electricity meter 
pulse setting 
1 (*3)

Setting number (xx00)

7

2

0

0

Setting number (xx01)

0

1

······

···

···

Setting number (xx98)

9

8

Setting number (xx99)

9

9

Set the ones digit and tens digit of the No. of the electricity meter pulse setting 
connected to CN135.

73

Electricity meter 
pulse setting 
2 (*3)

Setting number (00xx)

7

3

0

0

Setting number (01xx)

0

1

······

···

···

Setting number (98xx)

9

8

Setting number (99xx)

9

9

Set the hundreds digit and thousands digit of the electricity meter pulse setting 
connected to CN135.

90

Prohibited (Factory default)

9

0

0

0

*1:  Do not set this for outdoor units with Slave setting.
*2:  When electricity meter No. is set to “000” and “201 to 299”, the pulses input to 

CN135 become ineffective. Available setting number is "001" to "200"

*3:  When the electricity meter pulse setting is set to “0000”, the pulses input to CN135 

become ineffective. Available setting number is "0001" to "9999"

*4:  This item is not displayed for 072, 090, and 108 models.

(1)  Turn on the power of the outdoor unit and enter standby mode.
• When system is normal 

POWER/MODE lamp lights up. (ER-
ROR lamp is off.)

• When system is abnormal 

Check the settings as there is an error in the 
settings for outdoor unit address 
(DIP switch SET 3-1, 2) or number of con-
nected slave units (DIP switch SET 3-3, 4).

MODE
/NEXT

SELECT ENTER

POWER

MODE

ERROR

POWER/MODE 
lamp: ON

ERROR 
lamp: OFF

SELECT button

ENTER button

MODE/EXIT button

7-segment 
display: off

MODE
/NEXT

SELECT ENTER

POWER

MODE

ERROR

POWER/MODE 
lamp: ON

7-segment display: 
“-” display

ERROR lamp: 
Blinking

(2) Setting 

method

Use the “MODE/EXIT”, “SELECT”, 
and “ENTER” buttons to configure 
settings according to the proce-
dures below.
(If no setting is made, the factory 
default setting will be displayed.)

: Press the “MODE/EXIT” button

: Press the “SELECT” button

: Press the “ENTER” button.
: Press the “ENTER” button for 

more than 3 seconds.

1: Function setting

7-segment LED display (LED 105, LED 104)

(Flashing)

First 2 digits Last 2 digits

(When [F3] to [F9] are displayed, continue to press 
the “SELECT” button until [F2] is displayed.)

2:  Setting the first 

2 digits

3: Setting the last 2 digits

Continue to press the “SELECT” button until the 
desired number appears at the last 2 digits.

Every press of the 
“SELECT” button will 
change the setting 
number for the first 2 
digits.

(Continue to press the “SE-
LECT” button until the desired 
number appears at the last 2 
digits.)

Setting is complete when the lamp lights up

Press “ENTER” button to return to “2: Setting the 
first 2 digits” (If there is no operation for 5 seconds 
after the setting, the display will return to “2: Setting 
the first 2 digits”.)

Setting is complete when the lamp lights up

Press “ENTER” button to return to “2: Setting the 
first 2 digits” (If there is no operation for 5 seconds 
after the setting, the display will return to “2: Setting 
the first 2 digits”.)

EXIT: Press the “MODE/EXIT” button to cancel the setting mode.

9380545347-01_IM.indb   13

9380545347-01_IM.indb   13

11/29/2019   8:49:54 AM

11/29/2019   8:49:54 AM

Summary of Contents for AIRSTAGE AJ 072LELBH Series




















Reviews: