(Station address)
(Communications error processing)
(Timer)
(Baud rate)
(Data length)
(Parity check)
(Stop bits)
(No-response error detection time)
(Response interval)
(Protocol selection)
(Station address)
(Communications error processing)
(Timer)
(Baud rate)
(Data length)
(Parity check)
(Stop bits)
(No-response error detection time)
(Response interval)
(Protocol selection)
(Mode selection)
(Mode selection)
RS-485 Communication (Standard)
RS-485 Communication (Option)
Bus Link Function
Loader Link Function
1 to 255
0 : Immediately trip with alarm
1 : Trip with alarm after running for the period specified by timer y03
2 : Retry during the period specified by timer y13.If the retry fails,
trip with alarm . If it succeeds, continue to run.
3 : Continue to run
0.0 to 60.0
0 : 2400 bps
1 : 4800 bps
2 : 9600 bps
3 : 19200 bps
4 : 38400 bps
0 : 8 bits
1 : 7 bits
0 : None (2 stop bits for Modbus RTU)
1 : Even parity (1 stop bit for Modbus RTU)
2 : Odd parity (1 stop bit for Modbus RTU)
3 : None (1 stop bit for Modbus RTU)
0 : 2 bits
1 : 1 bit
0 : No detection
1 to 60
0.00 to 1.00
0 : Modbus RTU protocol
1 : FRENIC Loader protocol (SX protocol)
2: Fuji general-purpose inverter protocol
1 to 255
0 : Immediately trip with alarm
1 : Trip with alarm after running for the period specified by timer y13
2 : Retry during the period specified by timer y13. If the retry fails,
trip with alarm . If it succeeds, continue to run.
3 Continue to run
0.0 to 60.0
0 : 2400 bps
1 : 4800 bps
2 : 9600 bps
3 : 19200 bps
4 : 38400 bps
0 : 8 bits
1 : 7 bits
0 : None (2 stop bits for Modbus RTU)
1 : Even parity (1 stop bit for Modbus RTU)
2 : Odd parity (1 stop bit for Modbus RTU)
3 : None (1 stop bit for Modbus RTU)
0 : 2 bits
1 : 1 bit
0 : No detection
1 to 60
0.00 to 1.00
0 : Modbus RTU protocol
2 : Fuji general-purpose inverter protocol
Frequency command
Run command
0 : Follow H30 data
Follow H30 data
1 : Via field bus option
Follow H30 data
2 : Follow H30 data
Via field bus option
3 : Via field bus option
Via field bus option
Frequency command
Run command
0 : Follow H30 and y98 data
Follow H30 and y98 data
1 : Via RS-485 link (Loader)
Follow H30 and y98 data
2 : Follow H30 and y98 data
Via RS-485 link (Loader)
3 : Via RS-485 link (Loader)
Via RS-485 link (Loader)
1
-
0.1
-
-
-
-
1
0.01
-
1
-
0.1
-
-
-
-
1
0.01
-
-
-
-
-
s
-
-
-
-
s
s
-
-
-
s
-
-
-
-
s
s
-
-
-
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
1
0
2.0
3
0
0
0
0
0.01
1
1
0
2.0
3
0
0
0
0
0.01
0
0
0
Position control
Overload stopping, torque limit P
Function, torque limit I
Current control level
0.0 to 1000.0
-999 to 999
[P], 0 to 9999
-999 to 999
[P], 0 to 9999
0 to 999
0 to 9999
0 to 400
-999 to 999
0 to 9999
0 to 9999
0.0 to 1000.0
0 to 9999
0, 1
0, 1, 2
0, 1
0.000 to 2.000, 999
0.001 to 9.999, 999
50.0 to 150.0
(the start timer)
(Start point: MSD)
(Start point: LSD)
(Position preset: MSD)
(Position preset: LSD)
(Creep speed switch point: MSD)
(Creep speed switch point: LSD)
(Creep speed)
(Stopping position: MSD)
(Stopping position: LSD)
(Completion width)
(End timer)
(Coasting compensation)
(Stopping position specifying method)
(Position pre-set condition)
(Position detecting direction)
(Gain)
(Integral time)
0.1
1
1
1
1
1
1
1
1
1
1
0.1
1
-
-
-
0.001
0.001
0.1
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
0.0
0
0
0
0
0
0
0
0
0
0
0.0
0
0
0
0
999
999
100.0
s
p
p
p
p
p
p
Hz
p
p
p
s
p
-
-
-
-
s
%
Y2: Will not be copied if the rated input voltage differs from the source inverter.
N: Will not be copied.
*3 Reserved for the maker. Do not set any data.
<Changing, validating, and saving function code data when the motor is running>
: Impossible, : Possible (Change data with keys and then
save/validate it with key), : Possible (Change and validate data with
keys and then save it with key)
●
J codes: Application Functions
●
y codes: Link Functions
Func.
Code
Data
copy
*2
Name
Data setting range
Default setting
Min.
Unit
Func.
Code
Data
copy
*2
Name
Data setting range
Default setting
Min.
Unit
*1 When you make settings from the keypad, the incremental unit is restricted by the number of
digits that the LED monitor can display.
(Example) If the setting range is from -200.00 to 200.00, the incremental unit is as follows:
"1" for -200 to -100, "0.1" for -99.9 to -10.0, "0.01" for -9.99 to -0.01, "0.01" for 0.00 to 99.99,
and "0.1" for 100.0 to 200.0
*2 Symbols in the "Data copy" column
Y: Will be copied unconditionally.
Y1: Will not be copied if the rated capacity differs from the source inverter.
Functions
Settings
