manualshive.com logo in svg

FujiFilm FinePix S1500, Service Manual, Page: 123 / 142

Share
Download
FujiFilm FinePix S1500 Service Manual Download Page 123

5-1

FinePix S1500 Service Manual

5. Inspection

Confidential: FUJIFILM Service Center Use Only

5.  Inspection

5-1. 

Required Measuring Equipment

Parts number

Measuring equipment

Remarks

Power supply

AC adapter (AC-5V), Regurated power supply

Digital voltmeter

For general use

Ammeter

For general use (able to measure 1mA or less)

TV Monitor

TV monitor, minimum resolution 600 lines

CR0130900U9

DC COUPLER CP-04

Common with adjustment JIG

ZJ00580-100

POWER CABLE JIG

Common with adjustment JIG

ZJ00525-100

Macro Chart

Resolution confirmation

ZJ00885-100

LCD Inspection Data

For LCD inspection (downloaded from WEB.)

ZJ01021-100

Face Detection Test Chart Checking face detection operation

ZPU0512-100

SD CARD ULTRA2 1GB

To check SD card recording

5-2. 

Connection of Measuring Equipment

Use DC COUPLER CP-04 and POWER CABLE JIG.
The output current of the Regurated power supply must not become 2.5A or more.

DC COUPLER CP-04

Digital voltmeter

Regurated

Power supply

Ammeter

POWER CABLE JIG

FinePix S1500

Summary of Contents for FinePix S1500















































































































































Reviews:

No comments