manualshive.com logo in svg

FujiFilm FinePix S1500, Service Manual, Page: 119 / 142

Share
Download
FujiFilm FinePix S1500 Service Manual Download Page 119

FinePix S1500 Service Manual

4-61

4. Adjustments

Confidential: FUJIFILM Service Center Use Only

4-25.  Firmware Download

[Overview]

Replace the adjustment firmware with the product firmware.
Always execute the Firmware Download after completing the adjustments.

[Note]

•  Always download the latest version of the firmware.
•  Do not turn the camera off until the firmware Download is completed.

<Step 1>

Insert the firmware SD card into the camera.

<Step 2>

Set the camera into the DC COUPLER CP-04N and connect the AC adapter.

<Step 3>

Set the camera's power switch to "ON" while holding down 
the DISP/BACK button.

--> The firmware rewrite menu appears.

<Step 4>

Press the MENU/OK button to display the confirmation 
window.

<Step 5>

Press the Left button to select "OK" and then press the 
MENU/OK button.

FIRMWARE UPGRADE

FIRMWARE UPGRADE OK?
VERSION  :  1.xx  

�

  1.xx

SET

OK

CANCEL

FIRMWARE UPGRADE

USE AC ADAPTER FOR

FIRMWARE UPGREADE
VERSION  :  1.

xx

CANCEL

YES

Summary of Contents for FinePix S1500















































































































































Reviews:

No comments