Fuji Xerox DocuCentre S1810 Page 183 User Manual Download

Page: 183 / 202

Paper Jams

183

lem S

lving

Remove the jammed paper.
If the tray is empty, load paper.

Note

•

If the paper tears, check to make sure there
are no remaining shreds in the machine.

Push the tray in gently until it stops.

E-5: Paper Jams in Bypass Tray

Follow the steps below to clear a paper jam in the Bypass tray.

Remove the jammed paper by referring to "E-1: Paper Jam in Left Cover [A]" (P.180).

Inspect the inside (around the paper feed
entrance) of the Bypass tray, and remove the
jammed paper.

Important •

If multiple sheets of paper were loaded,
remove all the paper while you clear the
jam.

Note

•

If the paper tears, check to make sure there
are no remaining shreds in the machine.

If multiple sheets of paper were loaded, align the corners of the removed paper.

Insert the paper with the side to print on facing
down, aligning it so that its leading edge lightly
contacts the paper feed entrance.

Summary of Contents for DocuCentre S1810










































































































































































































Search results

Summary of Contents for DocuCentre S1810

Reviews:

Related manuals for DocuCentre S1810

Brands by name

Popular brands

Fuji Xerox DocuCentre S1810, User Manual

Search results

Summary of Contents for DocuCentre S1810

Reviews:

Related manuals for DocuCentre S1810

Brands by name

Popular brands