manualshive.com logo in svg

Fuji Xerox DocuCentre S1810, User Manual

Share
Download
Fuji Xerox DocuCentre S1810 User Manual Download Page 169

Network Related Problems

169

Pr

o

b

lem S

o

lving

11

Internet/Intranet Connection Problems

The table below lists possible causes and solutions for problems that might occur when 

connecting to the Internet or an intranet.

Unable to Connect to the Internet or an Intranet

Possible Cause

Remedy

The IP address has not been 
set correctly.

Check the IP address setting. If the IP address has not been 
set correctly, specify a fixed IP address or use DHCP or 
Autonet to resolve the IP address.

The IP gateway address has 
not been set correctly.

Enter the IP gateway address correctly when connecting to a 
proxy server or web server via an IP gateway.

The subnet mask has not 
been set correctly.

Set the subnet mask correctly, to match the environment in 
use.

The DNS server address has 
not been set correctly.

Check the DNS server address.

The DNS server selected 
cannot resolve the address.

Select a DNS server that can resolve the address.

z

When connecting via the proxy server
Set the IP address of a DNS server that can resolve the 
address of the proxy server.

z

When not connecting via the proxy server
Set the IP address of a DNS server that can resolve the 
destination address.

The setting of the address 
that does not use a proxy 
server is incorrect.

Confirm whether only addresses that do not use a proxy 
server are set. Even if addresses not through a proxy server 
are specified using the FQDN, if a server is directly accessed 
using its IP address, the registered server is not excluded. 
Set the address not to use a proxy server.
Likewise, even if you directly specify an address that does 
not use a proxy server, if a server is accessed with the 
FQDN, the registered server is not excluded. Set an IP 
address with the FQDN not to use a proxy server.

The connected server or 
proxy server is down.

Check whether the server or proxy server to connect to is 
working normally.

A network cable is 
disconnected or broken.

Check the network cable connections. The use of a 
spanning tree environment is recommended to create a 
network environment resistant to disconnections.

Unable to communicate due 
to the load on the server 
application.

Wait a while, then access the server again.

An error has occurred but is 
not displayed on the control 
panel.

Errors that occur while executing background processes are 
not displayed on the control panel. Print the Job History 
Report to check the execution results.

Summary of Contents for DocuCentre S1810











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands