background image

 
 

Command:  AOIWN 

 
Description:  

Allows sizing adjustments of the input source with respect to the output raster. 

Parameters: 

n – Right Edge 
n – Horizontal Width (Pixels) 
n – Bottom Edge 
n – Vertical Height (Lines) 
sclr – Scaler [A|B|M|P]; Scaler A | Scaler B | Main | Preview 

Example: 
AOIWN A? : Returns for Scaler A: =n n n n n, (=Right Edge, Horizontal Width, Bottom Edge, Vertical Height, Clock 
Samples per Line). 
 
 
 

 Command:  AVS

  t  m 

 
Description: Sets integration or presentation mode 
 
 

 

Set audio video mode   t[0,1] 0:integration  1:presentation     

 

 

m[1…3]    1: Video  2: Audio   3: Both 

 

 
Command:  

CHKSUM

 

 

Description:  

Returns the list of flash-stored file checksums

 

Parameters: 

None 

Example: 

CHKSUM: Returns the following. 
 

Flash-stored file checksums. 

 

 ab25 - spinc.rbf 
 4a6f - spoc.rbf 
 d4ec - spmx.rbf 
 2b69 - terminal.bin 
 57c6 - pm_menu.cs 
 d3ff - Compass S2.dwn 

 
 

Command:  CMDST? 

 

Description:  

Returns status of the last command that executed 

Parameters: 

None 

Example: 

CMDST? : 0 = Completed; 1 = Format Error; 2 = Range Error;  
3 = Execution Error; 4 = Command Not Available Error. 

 
 

Command:  COMCK op 
 

Description:  

Allows a remote control system to verify communications between itself and the Compass S2. 

Parameters: 

op – [D]ownload or [U]pload data 
n – Amount of data to upload or download. This is an optional parameter that defaults to 128 bytes. 

Example: 

COMCK U : After the terminating <CR>, the systems waits for 128 bytes to be sent. 

40 

                                                                           

Compass 

S

2

 

Summary of Contents for CN-2002






































































Reviews: