background image

Checklists 

 

AFTER-SALE  CHECKLIST:   

It  is  suggested  the  following  items  be  checked  sometime  during  the  first  six 

months operation of the disk. 

 

□  Check the entire disk for loose or missing hardware. 
 
□  Check for broken or damaged parts.  Make necessary repairs. 
 
□  Re-torque the hardware with special attention to the gang axle nuts and locks. 
 
□  Safety chain is properly installed and undamaged. 
 
□  If possible, run the disk to insure it is functioning properly. 
 
□  Check the bearing wear plates are present and not excessively worn. 
 
□  Visually  check  the  oil-bath  bearing  for  leaks.    If  parked  unused  for  a  long  period  in  extreme  weather 

conditions,  there  may  be  seepage  due  to  expansion  and  contraction  of  the  metal  duo-cone  seals.    This 
condition will correct itself when the disk is operated.  Lost oil should be replaced before operation. 

 
□  Review  the  entire  Operators  Manual  with  the  customer  and  stress  the  importance  of  proper  and  regular 

lubrication and safety precautions. 

 
□  Advise the customer of optional attachments that are available. 
 

Dat

e Checke

d_________________________  S

i

gnatur

e

___________________________________________________ __ 

 
 
 

EACH DAY OF OPERATION CHECKLIST  

 

 
□  Lubricate items required daily and those whose lubrication time is due. 
 
□  Look for loose or missing bolts and parts. 
 
□  Check hydraulic system for leaks and abraded hoses. 
 
□  Check tire pressures and wheel lug nuts. 
 
□  Check all pins have retaining hardware in place. 
 
□  Check all oil-bath bearing assemblies for leaks.  Check bearing wear plates are present. 
 
□  Be sure all gang components are tight on the axles and axle nuts are tight and axle locks are present. 
 
 
 

BEFORE EACH SEASON CHECKLIST

 

 
□  Be sure recommended lubrication is performed. 
 
□  Inspect all oil-bath bearing assemblies are tight and dry and if wear plates need replacement. 
 
□  Check hydraulic system for proper operation and leakage. 
 
□  Check tire pressures and wheel lug nuts.  Check for end play in wheel bearings and repack if necessary. 
 
□  Be sure proper operating adjustments have been made for your conditions. 
 

 
 
 

Summary of Contents for DH5410C



















































Reviews: