Fromm FS1 2109 V01 Series Manual Download Page 8 | Manualshive

Page: 8 / 49

background image

FROMM

FS1.2109-Manual 32.42XX.XXX.V01-V02-V03-EN08_R2.doc

It is forbidden to duplicate this manual or parts of it in any way or any form without written permission of the author © 2017

website: www.fromm-stretch.com

8

SAFETY INSTRUCTIONS

ATTENTION!

The following conditions have always to be satisfied, unless otherwise indicated in other
instructions in this manual.



This wrapping machine has been delivered by FROMM Stretch Wrapping Division and may only be

applied for wrapping of pallets / products which meet the requirements as mentioned in the
description of the machine in chapter TECHNICAL DATA.
Any other use of the machine as for the described purpose may cause danger due to damage to
the machine and/or the safety of the operator or other persons in the neighbourhood of the
machine.



Read this manual carefully before using the machine, and be aware of the residuals risks which could

not be excluded during the development of this machine.



In any case all the components must be disposed of by scrupulously complying with the

corresponding laws in force in the country in which the machine is used, and only by qualified
persons who are capable of assessing possible risks.



Only personnel trained for the purpose may operate the machine.



Use the emergency stop to halt the machine immediately.



Only trained electricians may perform electrical work on the machine.



Don’t find yourself close to the carriage when the machine is in operation. Be careful especially in
the lowering phase of the carriage. (Use the emergency stop to halt the machine immediately).



Don’t find yourself

near the turntable when the machine is in operation.

(Use the emergency stop to halt the machine immediately).



Don’t touch the pallet when the machine is in operation.
(Use the emergency stop to halt the machine immediately).



Don’t place or insert your hand and fingers between mast and carriage.
(Use the emergency stop to halt the machine immediately).



Don’t put your hand or fingers in the mast.
(Use the emergency stop to halt the machine immediately).



Don’t put your hand or fingers near the wheels for the carriage movement.
(Use the emergency stop to halt the machine immediately).



Don’t put your hand or fingers in the electrical box.
(Use the emergency stop to halt the machine immediately).



Don’t cross the space between the mast and turntable.
(Use the emergency stop to halt the machine immediately).



Don’t put your finger in the space between the turntable and the base-unit.
(Use the emergency stop to halt the machine immediately).

«
...
6
7
8
9
10
...
»

Summary of Contents for FS1 2109 V01 Series


















































Reviews:

No comments

Related manuals for FS1 2109 V01 Series

Brand: Calistair Pages: 44

Brand: ABB Pages: 36

Brand: ABB Pages: 40

Brand: ACCU-CHECK Pages: 104

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

Brand: ParaBody Pages: 5

The Wave Transformer

Brand: EarthQuaker Devices Pages: 21

Brand: TANDBERG Pages: 23

Brand: Backyard Play Systems Pages: 73

Brand: lancer Pages: 3

Brand: lancer Pages: 12

Brand: R2 Pages: 26

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: Quark-Elec Pages: 2

Brand: UEi Pages: 5

Brand: UGO BASILE Pages: 47

Brand: UFO Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands