Fromm FS1 2109 V01 Series Manual Download Page 36

Page: 36 / 49

FROMM

FS1.2109-Manual 32.42XX.XXX.V01-V02-V03-EN08_R2.doc

website: www.fromm-stretch.com

BASIC

OPERATING INSTRUCTIONS

Button

Explanation

Digital setting for adjusting carriage ascent / decent speed
(adjustment 1 to 9 step 1)

Digital setting for adjustment of number top wraps
(adjustment 1 to 9 step 1)

Digital setting for adjustment of number bottom wraps
(adjustment 1 to 9 step 1 )

Digital setting for adjusting turntable speed during bottom wraps
(adjustment 1 to 9 step 1)

Jog table. For the manual movement of the turntable

Carriage movement jog button.
Press once to raise the carriage. Press again to stop the movement.
Using the +/-

buttons it’s possible to increase decrease the speed.

Carriage movement jog button.
Press once to lower the carriage. Press again to stop the movement.
Using the +/-

buttons it’s possible to increase decrease the speed.

Press during the automatic cycle and the carriage will stop the movement during
activation of this button

1. Reset button. Reset the machine to home position.
2. After switching on the machine clear error E2 the control voltage is activated

again.

ACTUAL WRAPPED ROUNDS

Max value at counter is 99.999.999 Million rounds.

EXAMPLE 99.887.766

STARTIING from the first TWO digits until the last TWO digits

PRESS one time

= shown value P12 (99)

PRESS two times

= shown value P13 (88)

PRESS three times = shown value P14 (77)
PRESS four times

= shown value P15 (66)

P12

P13

P14

P15

Summary of Contents for FS1 2109 V01 Series


















































Search results

Summary of Contents for FS1 2109 V01 Series

Reviews:

Related manuals for FS1 2109 V01 Series

Brands by name

Popular brands

Fromm FS1 2109 V01 Series, Manual

Search results

Summary of Contents for FS1 2109 V01 Series

Reviews:

Related manuals for FS1 2109 V01 Series

Brands by name

Popular brands