Fröling T4e Operating Instructions Manual Download

Page: 62 / 76

❒ Loosen the twin wire clamp with pliers and remove the measurement line from the

under-pressure sensor cartridge

❒ Clean the measurement line with gentle compressed air

➥ WARNING! Do not direct compressed air into under-pressure sensor cartridge!

This could damage it!

❒ After cleaning, refit the measurement line

Depending on the design, port “-” (A) or “HI” (B)

5.4.3 Cleaning the Lambda probe

Rear flue pipe connection (optional)

❒ Remove the back insulating cover and thermal insulation upwards

❒ Remove the back insulating cover by pulling it up and fold the thermal insulation

down

❒ Loosen the spring bolts and open the front cover of the heat exchanger

Up to boiler type 60:

Starting at boiler type

80:

Servicing the system

Maintenance work by technicians

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Summary of Contents for T4e













































































Search results

Summary of Contents for T4e

Reviews:

Related manuals for T4e

Brands by name

Popular brands

Fröling T4e, Operating Instructions Manual

Search results

Summary of Contents for T4e

Reviews:

Related manuals for T4e

Brands by name

Popular brands